Farm King Model 1050 Скачать руководство пользователя страница 94

Страница: 94 / 174

Maintenance - 10" Backsaver Auger

2168 Lower Gearbox

Figure 153

Check the gearbox oil level every 50 hours or weekly.

Remove the fill / drain plug (Item 1)

[Figure 153]

from

the gearbox. Oil level should be at the bottom of the

plug hole.

If the oil level is low, add SAE 75W-90 synthetic gear

oil until the oil is at the bottom of the hole.

Changing Gear Oil

Remove the fill / drain plug (Item 1)

[Figure 153]

and

siphon all the gear oil from the gearbox.

Fill with SAE 75W-90 synthetic gear oil to the bottom

of the plug hole. Install fill / drain plug.

2168 Upper Gearbox

Figure 154

Check the gearbox oil level every 50 hours or weekly.
Remove the fill / drain plug (Item 1)

[Figure 154]

from

the gearbox. Oil level should be at the bottom of the

plug hole.
If the oil level is low, add SAE 75W-90 synthetic gear

oil until the oil is at the bottom of the hole.

Changing Gear Oil

Remove the fill / drain plug (Item 1)

[Figure 154]

and

siphon all the gear oil from the gearbox.
Fill with SAE 75W-90 synthetic gear oil to the bottom

of the plug hole. Install fill / drain plug.

Cleaning And Inspection
NOTE: Inspect the driveline components, replace all

damaged or worn components.

Use solvent to clean the shaft and tube. Use

compressed air to dry and remove excess solvent from

the parts.
Apply a light coat of grease to the shaft and the tube

end.
Use solvent to clean the slide collars, yokes, crosses

and bearings. Use compressed air to dry the parts.
Apply a light coat of grease to the inside of the slide

collars.

960953

960952

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды