Farm King Model 1050 Скачать руководство пользователя страница 95

Страница: 95 / 174

Maintenance - 10" Backsaver Auger

AXLE

Wheel Lug Nut Torque

Check the torque on wheel lug nuts daily. Tighten lug

nuts to 80 - 100 lb. / ft. (108 - 135 N•m) torque.

Tire / Wheel Replacement

Empty the Backsaver Auger (if required).

Park the tractor / equipment on a flat level surface.

Place all controls in neutral, engage the park brake,

stop the engine and wait for all moving parts to stop.

Leave the operator’s position.

Place chock blocks behind and in front of the auger

tire(s).
Place a jack under the axle frame on the side the

wheel is to be replaced. Raise the jack until the wheel

is slightly off the ground.

NOTE: Place blocks under the frame to help secure the

auger when wheel is raised off the ground.

Figure 155

Remove the wheel nuts and tire from the hub.

Install the new tire with the valve stem facing out

(both sides). Install the eight wheel nuts (both sides)

[Figure 155]

Tighten wheel nuts in a criss-cross pattern

[Figure

155]

. Tighten wheel nuts to 80 - 100 lb. / ft. (108 -

135 N•m) of torque.

AVOID INJURY OR DEATH

Before you leave the operator’s position:
•

Always park on a flat level surface.

•

Place all controls in NEUTRAL.

•

Engage the park brake.

•

Stop the engine and remove the key.

•

Wait for all moving parts to stop.

AVOID INJURY OR DEATH

•

The parking brake must be engaged before

leaving the operator’s position. Rollaway can

occur because the transmission may not prevent

machine movement.

•

Always chock tires before performing any

maintenance or service.

B-0590

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды