Farm King Model 1050 Скачать руководство пользователя страница 74

Страница: 74 / 174

Operation - 10" Backsaver Auger

Connecting Hydraulic Hoses

NOTE: Make sure the quick couplers are fully

engaged. If the quick couplers do not fully

engage, check to see that the couplers are the

same size and type.

To Connect:

Figure 126

Pull back on the collar of the female coupler, push

couplers together, release the collar when the

couplers are fully engaged and locked

[Figure 126]

Install the lift cylinder quick coupler hose (Item 1)

[Figure 126]

Install the two control valve quick coupler hoses (Item

[Figure 126]

(if equipped).

To Disconnect:

Pull back on the collar and pull the male coupler out to

disconnect.

HIGH PRESSURE FLUID HAZARD

To prevent serious injury or death from high pressure

fluid:
•

Relieve pressure on system before repairing or

adjusting.

•

Wear proper hand and eye protection when

searching for leaks. Use wood or cardboard

instead of hands.

•

Keep all components in good repair.

•

Contain and dispose of any oil leakage in an

environmentally safe manner.

•

Thoroughly clean the quick couplers before

making connections. Dirt can quickly damage the

system.

B-0531A

AVOID BURNS

Hydraulic fluid, tubes, fittings and quick couplers can

get hot when running equipment. Be careful when

connecting and disconnecting quick couplers.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды