Farm King Model 1050 Скачать руководство пользователя страница 44

Страница: 44 / 174

Assembly - 10" Backsaver Auger

Figure 59

Align the intake lift boom (Item 1) with the mounting

plate on the bottom tube section. Install four 1/2” x 1-

1/2” bolts (Item 2)

[Figure 59]

, down through the

intake lift boom and mounting plate. Install one 1/2”

flat washer and 1/2” lock nut the four 1/2” bolts.

Tighten the bolts and nuts.

Figure 60

NOTE: Remove clamp section of two 1/2” cable

clamps. Use only the u-bolts and nuts.

NOTE: When installing the u-bolt around the two

cables, place the short cable into the u-bolt

first (both sides).

Install one 1/2” cable clamp (Item 1)

[Figure 60]

around both the long and short cables, then install into

the bridging yoke (on the bottom tube section) (both

sides). Do not tighten cable clamp at this time.

Figure 61

Install one 1/2” cable clamp (Item 1)

[Figure 61]

around the long cable, then install into the upper

bridging yoke (on the center tube section). Do not

tighten cable clamp at this time.

B-0652

B-0658

B-0657

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды