Farm King Model 1050 Скачать руководство пользователя страница 68

Страница: 68 / 174

Operation - 10" Backsaver Auger

by either adjusting the tractor hitch, the auger hitch or

both

[Figure 117]

For checking PTO driveline see “PTO Driveline” on

page 69.

Entering And Leaving The Operator’s Position

Entering The Operator’s Position

Move to the operator’s position, start the engine and

release the parking brake.

Leaving The Operator’s Position

Park the tractor / equipment on a flat level surface.

Place all controls in neutral, engage the park brake,

stop the engine and wait for all moving parts to stop.

Leave the operator’s position.

INITIAL SET-UP

Connecting The Backsaver Auger To The Tractor

Always inspect the tractor’s drawbar and Backsaver

Auger’s hitch before connecting. See the tractor’s

owner’s manual.
Verify that the tractor’s drawbar is adjusted correctly

for use with the Backsaver Auger. (See “Drawbar

Adjustment” on page 65.)
Enter the operator’s position. (See “Entering The

Operator’s Position” on page 66.)
Move the tractor into position in front of the

Backsaver Auger.

Move the tractor backwards, aligning the drawbar

with the Backsaver Auger hitch.

NOTE: The jack may need to be lowered or raised for

proper alignment of the drawbar and hitch.

If the Backsaver Auger hitch needs to be adjusted,

stop the tractor when drawbar is just in front of the

Backsaver Auger hitch.
Leave the operator’s position. (See “Leaving The

Operator’s Position” on page 66.)

Follow the instructions in your tractor’s operation

manual for the correct procedure.

AVOID INJURY OR DEATH

Before you leave the operator’s position:

•

Always park on a flat level surface.

•

Place all controls in NEUTRAL.

•

Engage the park brake.

•

Stop the engine and remove the key.

•

Wait for all moving parts to stop.

AVOID INJURY OR DEATH

Before moving the tractor, look in all directions and

make sure no bystanders, especially small children

are in the work area. Do not allow anyone between

the tractor and the equipment when backing up to

the equipment for connecting.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды