Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 74

Страница: 74 / 424

BlackDiamond 12800 Series Modules

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

I/O Port LEDs

Table 13

describes the LED activity for each port on the GM-20XT, GM-20XTR, XM-2X and XM-2XR I/O

modules.

Table 14

describes the LED activity for each port on the BlackDiamond GM-20T I/O module.

GM-20T I/O Module

Figure 32

shows the GM-20T I/O module.

Figure 32: GM-20T I/O module

The GM-20T I/O module has 20 autosensing 10/100/1000BASE-T ports that use standard RJ-45
connectors.

Table 13: Port LEDs for the BlackDiamond GM-20XT, GM-20XTR, XM-2X and XM-2XR I/O modules

LED

Color

Meaning

Port

Solid green

Link up

Slow green blinking

Port disabled

Amber blinking

Activity

Off

Link down

Table 14: Port LEDs for the BlackDiamond GM-20T module

LED

Color

Meaning

Port with power enabled

Solid amber

Link up

Slow amber blinking

Port disabled

Amber blinking

Activity

Slow amber blinking

Link down

Blinking amber/green

Power fault or insufficient power

Port with power disabled

Solid green

Link up

Slow green blinking

Port disabled

Green blinking

Activity

Off

Link down

Blinking amber/green

Power fault or insufficient power

EX_152h

Module status

LEDs

10/100/1000BASE-T

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды