Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 424

background image

Extreme Networks 700/1200 W AC PSU

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

149

Removing an Extreme Networks 700/1200 W AC PSU

CAUTION

The AC PSU may be hot to the touch; use thermal protective gloves when handling the 700/1200 W AC PSU during
removal.

To remove an Extreme Networks 700/1200 W AC PSU:

1

Attach an ESD-preventive wrist strap to your wrist and connect the metal end to the ground
receptacle that is located on the top-left corner of the switch front panel (if not already attached).

2

For the AC power cord:

a

If you are going to use the same AC power cord for the new unit, you do not need to touch the
power cord at all.

b

If you are going to use a new AC power cord, remove the power cord retaining bracket. (See

Chapter 2, “BlackDiamond AC Power Cord Retaining Brackets”

for information on removing the

power cord retaining bracket and re-installing it.) Connect the AC power cord to the AC input on
the front of the switch and to the wall outlet on the other end. Then, re-install the power cord
retaining bracket.

3

Lift the handle up on the Extreme Networks 700/1200 W AC PSU.

4

Pull on the handle of the Extreme Networks 700/1200 W AC PSU to remove it from the power
supply bay.

5

Place both hands underneath the Extreme Networks 700/1200 W AC PSU to support the weight
after it is pulled out from the switch.

NOTE

Leave the ESD strap permanently connected to the switch, so that the strap is always available when you need to
handle ESD-sensitive components.

«
...
147
148
149
150
151
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: GE Страницы: 20

Бренд: Hama Страницы: 18

Бренд: B&B Electronics Страницы: 26

Бренд: B&B Electronics Страницы: 15

Бренд: B&B Electronics Страницы: 45

Бренд: Delta Страницы: 4

MMAC-Plus 9H423-26

Бренд: Cabletron Systems Страницы: 14

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Hamlet Страницы: 4

Бренд: SUCO Страницы: 2

Бренд: Black Box Страницы: 10

TGS-1080-M12 Series

Бренд: ORiNG Страницы: 2

Бренд: FS Страницы: 43

Бренд: Wetekom Страницы: 34

LMP-0602 24-V2 Series

Бренд: ANTAIRA Страницы: 2

Бренд: Key Digital Страницы: 20

8265 Nways ATM Switch

Бренд: IBM Страницы: 100

SBX 95 SE - AV Control 4

Бренд: Vivanco Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды