Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 267 | Manualshive

Страница: 267 / 424

background image

Summit X450a Series Switches

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

267

NOTE

For information regarding these compatible Summit option cards, see

“Summit XGM2-2xn Option Card” on

page 297

or

“Summit XGM2-2xf Option Card” on page 302

.

●

Management port

■

Used to connect the system into a parallel management network for administration.

OR

■

Used to connect an Ethernet cable directly from your laptop into the management port to view
and locally manage the switch configurations.

●

Two LEDs for the management port, located in the bottom corners of the port.

●

Two high-performance stacking ports

●

Redundant power input connector for an optional, redundant Extreme External Power Supply (see

“EPS-500 External Power Supply Unit” on page 317

for complete details). The connecting redundant

power supply cable is shipped with the EPS-500 power supply.

●

AC power socket

The switch automatically adjusts to the supply voltage. The power supply operates from 100 VAC to
240 VAC.

Summit X450a-48tDC Switch

The Summit X450a-48tDC switch includes the following:

●

44 fixed 10/100/1000 BASE-T ports that deliver high-density copper connectivity for 44 Gbps in
1.75-inch (1U) form factor (ports 1-44)

●

Four combination ports that provide 10/100/1000 BASE-T or mini-GBIC connectivity for 4 Gbps of
copper or fiber connectivity (ports 45-48)

NOTE

For information about mini-GBICs, see

“Mini-GBIC Interfaces” on page 338

.

●

Two high-performance stacking ports

●

Optional:

■

Summit XGM2-2xn option card, which allows you to add up to two 10 Gigabit XENPAK modules

■

Summit XGM2-2xf option card, which allows you to add up to two 10 Gigabit XFP modules

NOTE

For information regarding these compatible Summit option cards, see

“Summit XGM2-2xn Option Card” on

page 297

or

“Summit XGM2-2xf Option Card” on page 302

.

●

Optional: EPS-150DC External Power Module (Model No. 10909), which is the redundant power
supply for use with the Summit X450a-48tDC switch. When this switch is used with the EPS-150DC,
the power supplies (internal and redundant) are fully fault tolerant and load-sharing. If one power
supply fails, the other power supply will provide sufficient power to operate the switch.

«
...
265
266
267
268
269
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 281

Baseline 2226 Plus

Бренд: 3Com Страницы: 4

Бренд: Eaton Страницы: 8

Бренд: LAUMAS Страницы: 40

IO-Link BNI LH1-303-S11-K091

Бренд: Balluff Страницы: 12

Бренд: Techroutes Страницы: 22

Бренд: Black Box Страницы: 2

SRS Lighting DTS16F-DIN

Бренд: plasa Страницы: 4

RoamAbout RBT-4102-BG

Бренд: Enterasys Страницы: 72

Бренд: GE Страницы: 2

Бренд: ASTEK Страницы: 3

Бренд: hager Страницы: 4

FlexFabric 5940 Series

Бренд: Hewlett Packard Enterprise Страницы: 123

Бренд: EtherWAN Страницы: 2

Бренд: EtherWAN Страницы: 2

SI1P-SH-DVI-UCAC

Бренд: Black Box Страницы: 16

LiteWave LS105G

Бренд: TP-Link Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды