Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 424

background image

BlackDiamond 12800 Series I/O Modules

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

73

The MSM-5 and MSM-5R modules have the following features on the front panel:

●

Console port—The DB9 serial console port is used to connect a terminal, allowing you to perform
local management.

●

Management port—The 10/100 Mbps Ethernet management port allows you to connect an Ethernet
cable directly from your laptop to the management port to view and locally manage the switch
configurations. This port can also be used to connect the system to a parallel management network
for administration.

●

Compact flash—You can insert an external compact flash memory card into this slot. (See

Chapter 2

for more information about Extreme Networks-supported compact flash cards.)

●

Reset—Use the Reset button to reset the MSM without removing the module from the chassis.

BlackDiamond 12800 Series I/O Modules

No configuration information is stored on the I/O modules; all configuration information is stored on
the MSMs.

When a BlackDiamond 12800 series switch is powered on, the software generates a default
configuration for any slots that contain I/O modules. The default configuration allows the I/O module
ports to participate in the VLAN named

default

. The default configuration for the I/O module is not

preserved unless you explicitly save the configuration to NVRAM.

You can configure parameters of an I/O module after it is installed, or preconfigure a slot for a certain
type of module and configuration. The preconfigured information is applied to the module after it is
inserted. If you preconfigure a slot for a specific module type and then insert a different type of module,
the module reverts to its default configuration.

NOTE

See the

ExtremeXOS 12.0 Concepts Guide

and the

ExtremeXOS 12.0 Command Reference Guide

for more

information about configuring the modules.

I/O Module LEDs

Table 12

describes the LED activity for the BlackDiamond 12800 series I/O modules.

Table 12: BlackDiamond 12800 series switch I/O module LEDs

LED

Color

Meaning

Status

Green blinking

Normal operation

Amber blinking

Configuration error, hardware failure, diagnostic
failure, or other severe module error

Off

No power

DIAG

Off

Normal operation

Amber blinking

Diagnostics in progress

Amber

Diagnostic failure

«
...
71
72
73
74
75
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: D-Link Страницы: 14

DMS-1250 Series

Бренд: D-Link Страницы: 38

Бренд: Erbe Страницы: 118

Бренд: Dexon Страницы: 31

TM-1-8210 Series

Бренд: Eaton Страницы: 3

Cooper Power Systems LCR 6200 RFN

Бренд: Eaton Страницы: 8

Бренд: Free-Way Switch Страницы: 6

Бренд: Net Generation Страницы: 38

Бренд: N-Tron Страницы: 169

Бренд: Digitus Страницы: 10

Бренд: Anigmo Страницы: 2

Бренд: S&C Страницы: 23

SuperStack II Switch 1100

Бренд: 3Com Страницы: 6

Бренд: MyRepublic Страницы: 7

Бренд: CYP Страницы: 44

Бренд: CYP Страницы: 48

Бренд: HP Страницы: 22

Бренд: HP Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды