Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 347 | Manualshive

Страница: 347 / 424

background image

Mini-GBIC Interfaces

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

347

Extreme Networks recommends the following guidelines when installing or replacing mini-GBICs on an
active network:

●

Use the same type of mini-GBIC at each end of the link, except for the 1000BX mini-GBIC. The
1000BX mini-GBIC consists of two SFP optical devices, the 1000BASE-BX-U SFP and the
1000BASE-BX-D SFP, which must be used as a pair to allow for a single fiber bidirectional
connection.

●

Connect one end of the link to the Tx port. Without an attenuator, measure the total loss from the Tx
port to the other site of the link. The total loss must not exceed the total optical system budget.

Installing and Removing a Mini-GBIC

You can add or remove mini-GBICs from your switch without powering off the system.

Figure 238

shows the types of mini-GBIC modules and connectors.

NOTE

The 1000BX mini-GBIC consists of two SFP optical devices, the 1000BASE-BX-U SFP (Module C) and the
1000BASE-BX-D SFP (Module D), which must be used as a pair to allow for a single fiber bidirectional
connection.See

Figure 238

.

Figure 238: Mini-GBIC modules and connectors

SH_019

Module A

Module B

Module C

Blue

handle

Module D

1000BX mini-GBIC

Purple

handle

«
...
345
346
347
348
349
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: Ubisys Страницы: 40

Бренд: Xantech Страницы: 2

TRIPP LITE Series

Бренд: Eaton Страницы: 8

DXS-3410 Series

Бренд: D-Link Страницы: 54

Бренд: StarTech.com Страницы: 2

Бренд: IOGear Страницы: 10

AMX ENOVA DVX-3250HD-SP

Бренд: Harman Страницы: 119

Бренд: Manhattan Страницы: 4

Бренд: Cabletron Systems Страницы: 54

Бренд: TESmart Страницы: 4

Бренд: SICK Страницы: 299

Бренд: Versa Technology Страницы: 26

Бренд: Lanpro Страницы: 16

Бренд: J-Tech Digital Страницы: 81

Бренд: ATEN Страницы: 2

Бренд: AV Link Страницы: 2

IES6300PRO Series

Бренд: 3onedata Страницы: 5

Бренд: Led Control Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды