manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

Table of Contents

 

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

11

Chapter 22: Summit External Power Supplies (EPS) ...................................................................... 307

Overview ................................................................................................................................307

Safety ....................................................................................................................................308

EPS-160 External Power Module (with EPS-T) ...........................................................................309

Installing an EPS-160 External Power Module .....................................................................310

Rack Mounting the EPS-T ............................................................................................310
Installing an EPS-160 into an EPS-T ............................................................................311
Connecting the EPS-160 .............................................................................................311

Removing an EPS-160 from an EPS-T.................................................................................312

EPS-LD External Power Supply Unit..........................................................................................313

Installing an EPS-LD .........................................................................................................313

Rack-mounting the EPS-LD ..........................................................................................313
Connecting the EPS-LD to the Switch............................................................................314
Connecting the EPS-LD to Power ..................................................................................316

Removing an EPS-LD ........................................................................................................316

EPS-500 External Power Supply Unit........................................................................................317

Installing and Removing an EPS-500 ..................................................................................318

Rack-mounting an EPS-500 unit ..................................................................................318
Connecting the EPS-500 .............................................................................................319
Removing an EPS-500 unit ..........................................................................................321

EPS-150DC External Power Module (with EPS-T2).....................................................................321

Installing an EPS-T2 .........................................................................................................321

Pre-Installation Requirements ......................................................................................322
Rack Mounting the EPS-T2 ..........................................................................................322

Installing an EPS-150DC ...................................................................................................322

Connecting the DC Wiring Harness to the DC Source Voltage ...........................................323
Installing an EPS-150DC Unit into an EPS-T2 ...............................................................324
Connecting the DC Wiring Harness to the DC Power Socket on the EPS-150DC .................325
Connecting the EPS-150DC to a Switch ........................................................................325

Removing an EPS-150DC ..................................................................................................327

EPS-600LS External Power Module ..........................................................................................328

Power Supply Overview ......................................................................................................328

Single 600-LS Module Configuration: Redundant PoE Power...........................................328
Dual 600-LS Module Configuration: Full Power ..............................................................329
Triple 600-LS Module Configuration: Full Redundant Power............................................329
Internal-to-External PSU Transfer .................................................................................329

Internal PSU failure with single EPS-600LS module.................................................329
Two or Three EPS-600LS modules ..........................................................................329

External to Internal PSU Transfer..................................................................................329

Active Internal PSU with single 600-LS module failure .............................................329
Inactive Internal PSU with a dual EPS-600LS configuration and module failure ..........329
Disconnecting the EPS-C/EPS-600LS......................................................................330

Installing an EPS-C Chassis ...............................................................................................330

Pre-Installation Requirements ......................................................................................330
Rack-Mounting the EPS-C ............................................................................................330

Installing an EPS-600LS ...................................................................................................332
Removing an EPS-600LS...................................................................................................334

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

CALIENT S320 Hardware User'S Manual preview
S320
Бренд: CALIENT Страницы: 46
CALIENT S320 Getting Started Manual preview
S320
Бренд: CALIENT Страницы: 42
Eaton Cutler-Hammer Quick Start Instructions preview
Cutler-Hammer
Бренд: Eaton Страницы: 8
3Com 4210G Series Configuration Manual preview
4210G Series
Бренд: 3Com Страницы: 1133
Tripp Lite B310-701-4K Owner'S Manual preview
B310-701-4K
Бренд: Tripp Lite Страницы: 80
CalDigit Super Share Quick Start Manual preview
Super Share
Бренд: CalDigit Страницы: 13
J-Tech Digital JTECH-4KPIP0401 Operating Instructions Manual preview
JTECH-4KPIP0401
Бренд: J-Tech Digital Страницы: 10
Comprehensive CVG-21RCA User Manual preview
CVG-21RCA
Бренд: Comprehensive Страницы: 12
Rowley R-TEC Automation RTMWSR15C Manual preview
R-TEC Automation RTMWSR15C
Бренд: Rowley Страницы: 10
socomec STATYS series Operating Manual preview
STATYS series
Бренд: socomec Страницы: 38
H3C S6812 Series Installation Manual preview
S6812 Series
Бренд: H3C Страницы: 77
WAGO 852-1111 Mounting, Installation And Handling preview
852-1111
Бренд: WAGO Страницы: 36
Generac Power Systems TRANSFER SWITCH Warranty Information Booklet preview
TRANSFER SWITCH
Бренд: Generac Power Systems Страницы: 1
EtherWAN EX78900X Series Installation Manual preview
EX78900X Series
Бренд: EtherWAN Страницы: 2
ENSIM SENSORS DX-ELB 11 Operating Manual preview
DX-ELB 11
Бренд: ENSIM SENSORS Страницы: 15
rackit MRS-815 Installer/User Manual preview
MRS-815
Бренд: rackit Страницы: 24
Microsens MS453514M Quick Installation Manual preview
MS453514M
Бренд: Microsens Страницы: 11
Analog way Smart Vu LE User Manual preview
Smart Vu LE
Бренд: Analog way Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды