Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 135

Страница: 135 / 424

Grounding the BlackDiamond 10808 Chassis

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

135

To ground the chassis:

Locate the grounding point on the back of the chassis (

Figure 81

Figure 81: Back of BlackDiamond 10808 chassis

Strip 0.5-inch (1.2-cm) of insulation from the stranded copper wire cable.

Insert the stripped wire into the cable lug.

CAUTION

Be sure that no copper is visible between the lug and the cable insulation.

Crimp the lug onto the cable according to the manufacturer’s specifications.

Insert the screws through the lug and into the grounding point on the back of the chassis.

Connect the other end of the wire to a known reliable earth ground point at your site.

EX_007A

Fan trays

Grounding
point

Power supply

controllers

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды