manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

 

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

3

Table of Contents

Preface......................................................................................................................................... 15

Introduction .............................................................................................................................15

Conventions..............................................................................................................................16

Related Publications .................................................................................................................16

Part 1: Site Preparation

Chapter 1: Site Preparation............................................................................................................ 21

Planning Your Site ....................................................................................................................22

Meeting Site Requirements ..................................................................................................22
Evaluating and Meeting Cable Requirements..........................................................................22
Meeting Power Requirements ...............................................................................................22

Meeting Site Requirements ........................................................................................................22

Operating Environment Requirements ...................................................................................23

Building and Electrical Codes .........................................................................................23
Wiring Closet Considerations ..........................................................................................24
Temperature .................................................................................................................24
BlackDiamond Family Chassis Spacing Requirements .......................................................25
Summit Family of Switches Spacing Requirements...........................................................25
BlackDiamond Family Chassis Airflow Requirements ........................................................25
Electrostatic Discharge ..................................................................................................27
Humidity ......................................................................................................................27

Rack Specifications and Recommendations ...........................................................................27

Mechanical Recommendations for the Rack .....................................................................28
Protective Grounding for the Rack...................................................................................28
Space Requirements for the Rack ...................................................................................29
Securing the Rack .........................................................................................................29

Evaluating and Meeting Cable Requirements ...............................................................................30

Cabling Standards ...............................................................................................................30
Cable Labeling and Record Keeping ......................................................................................30
Installing Cable...................................................................................................................31

Fiber Optic Cable ..........................................................................................................33
Cable Distances ............................................................................................................33

RJ-45 Connector Jackets .....................................................................................................34
Radio Frequency Interference ...............................................................................................35
Making Network Interface Cable Connections .........................................................................35

Meeting Power Requirements .....................................................................................................36

LAN Systems ......................................................................................................................36
Power Supply Requirements .................................................................................................36
PoE Devices .......................................................................................................................37
AC Power Cable Requirements..............................................................................................37

Replacing the Power Cable .............................................................................................37

Uninterruptible Power Supply Requirements ..........................................................................37

UPS Features................................................................................................................38
Selecting a UPS ............................................................................................................38

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

H3C s5800 series Configuration Manual preview
s5800 series
Бренд: H3C Страницы: 22
H3C S5500-EI series Quick Start preview
S5500-EI series
Бренд: H3C Страницы: 2
LAUMAS TLB Installation And User Manual preview
TLB
Бренд: LAUMAS Страницы: 40
Black Box LB9019A Installation preview
LB9019A
Бренд: Black Box Страницы: 2
plasa SRS Lighting DTS16F-DIN Instruction Manual preview
SRS Lighting DTS16F-DIN
Бренд: plasa Страницы: 4
RDL EZ-HSX4 Installation And Operation Manual preview
EZ-HSX4
Бренд: RDL Страницы: 4
Gilat SkyEdge II-c Capricorn Pro 4 AC Series Installation Notes preview
SkyEdge II-c Capricorn Pro 4 AC Series
Бренд: Gilat Страницы: 2
Silent Gliss 0913 Installation, Programming And Operation Instructions preview
0913
Бренд: Silent Gliss Страницы: 4
N-Tron NTSFP-LX-40 User Manual & Installation Manual preview
NTSFP-LX-40
Бренд: N-Tron Страницы: 20
Eaton AGswitch Instructions Manual preview
AGswitch
Бренд: Eaton Страницы: 36
Qlogic SANbox 5000 Series Instructions preview
SANbox 5000 Series
Бренд: Qlogic Страницы: 2
Clas Ohlson EMT445PCS Instruction Manual preview
EMT445PCS
Бренд: Clas Ohlson Страницы: 4
ddtop UQK-400 Operation Manual preview
UQK-400
Бренд: ddtop Страницы: 10
ELPRO TZ04 Installation And Use Manual preview
TZ04
Бренд: ELPRO Страницы: 8
I-Tech NVCIP800 User Manual preview
NVCIP800
Бренд: I-Tech Страницы: 29
3onedata IES6200-PN-16T4GS-2P48 Quick Installation Manual preview
IES6200-PN-16T4GS-2P48
Бренд: 3onedata Страницы: 3
Black Box LE2650A Specifications preview
LE2650A
Бренд: Black Box Страницы: 2
Grizzly G8988 Instructions preview
G8988
Бренд: Grizzly Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды