Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 188

Страница: 188 / 424

Installing BlackDiamond Series Modules

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

188

Installing or Removing an External Compact Flash Memory Card

You do not need to power off the system or remove the MSM from the chassis to install or remove an
external compact flash memory card.

You need an ESD-preventive wrist strap to install a compact flash memory card.

To install the memory card:

Attach the ESD-preventive wrist strap to your wrist and connect the metal end to the ground
receptacle on the chassis front panel.

Locate the compact flash slot on the MSM, as shown in

Figure 116

Figure 116: Typical compact flash slot location (BlackDiamond 8800 series MSM)

Hold the memory card between your thumb and forefinger.

For the BlackDiamond 8800 and 12800 series switches, the side with the ridge faces toward the
bottom of the chassis.

For the BlackDiamond 10808 switch, the side with the ridge faces to the left of the chassis.

Slide the card into the compact flash slot until you feel resistance.; a portion of the card will protrude
from the slot.

Carefully push the card until it is seated into the slot. The card should be fully inserted, or seated,
inside the slot.

To verify that the card is fully seated, use the

show memorycard

command.

To remove the external compact flash memory card:

Use the

eject memorycard

command to ensure that you will not lose any data when you remove

the card.

After you use the

eject memorycard

command, you can physically remove the card from the

external compact flash slot on the MSM. For more information about the

eject memorycard

command, see the

ExtremeXOS 12.0 Concepts Guide

Attach the ESD-preventive wrist strap to your wrist and connect the metal end of the strap to the
ground receptacle on the chassis front panel.

Locate the black release pin just above the compact flash slot.

Press the release pin until the card releases from the slot.

The card releases to an intermediate position; the card remains partially inserted but is no longer
seated in the slot.

Remove the card completely and place it in a safe location.

Compact flash

Console port

ASP038B

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды