Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 372 | Manualshive

Страница: 372 / 424

background image

Safety Information

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

372

Installing Power Supply Units

For the ratings and power requirements of each power supply unit, see

Appendix B, “Technical

Specifications”

or the data sheet for the power supply at

http://www.extremenetworks.com

.

WARNING!

Be sure that the following requirements are satisfied when installing all Extreme Networks power supplies.

Make sure to satisfy the following requirements:

●

Plug power supplies only into properly grounded electrical outlets to help prevent electrical shock
and comply with international safety standards.

●

Use only power cords that are certified for use within the country of use. Do not attempt to modify
AC power cords.

●

The wall outlet must be installed near the equipment and be easily accessible for quick disconnect.

●

Make sure the voltage and frequency of your power outlet match the equipment’s system’s electrical
ratings. The building and/or power source must provide overload protection.

●

Use a surge suppressor, line conditioner, or uninterruptible power supply to protect the system from
momentary increases or decreases in electrical power.

●

For hot-swappable power supplies, do not slam the PSU into the bay.

●

If multiple power supplies are used in a switch, connect each power supply to a different,
independent power source. If a single power source fails, it will affect only that power supply to
which it is connected. If all the power supplies on a single switch are connected to the same power
source, the entire switch is vulnerable to a power failure.

WARNING!

Extreme Networks 325 W DC PSUs do not have switches for turning the unit on and off. Make sure that the DC
circuit is de-energized before connecting or disconnecting the DC power cord at the DC power socket on the Extreme
Networks 325 W DC PSU.

Wiring the 325 W DC PSU DC power cord to your facility DC source voltage must be performed by a qualified,
licensed electrician.

Extreme Networks 325 W AC PSUs do not have switches for turning the unit on and off. Remove the wall plug from
the electrical outlet to disconnect the power to an Extreme Networks 325 W AC PSU. Make sure that this
connection is easily accessible.

Do not connect the power supply into an electrical outlet when the power supply is outside the chassis; doing so
would expose a hazardous energy and poses a potential shock and fire hazard.

Do not put your hand into an open power supply bay when a power supply is not present. Empty power supply bays
require a cover plate at all times.

«
...
370
371
372
373
374
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: 4O3A Страницы: 2

PIXIE Smart Switch G3

Бренд: SAL Страницы: 2

MicroHub GUH274W3

Бренд: IOGear Страницы: 1

Бренд: Nobile Страницы: 2

Nexoos 370 Series

Бренд: Soyntec Страницы: 7

Бренд: KanexPro Страницы: 35

Бренд: C&C TECHNIC Страницы: 2

Бренд: KinAn Страницы: 5

Бренд: Guntermann & Drunck Страницы: 8

Бренд: LEGRAND Страницы: 197

Бренд: Valcom Страницы: 1

Бренд: Conrad Страницы: 8

EWS-series EWS2910P-Kit-300

Бренд: EnGenius Страницы: 6

Бренд: Rolls Страницы: 2

MPD-DS-WML-NFDS Series

Бренд: Larson Electronics Страницы: 2

Бренд: Hendrickson Страницы: 16

Бренд: Pilz Страницы: 8

Бренд: mind alive Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды