Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 424

background image

Specifications

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

171

Power Supply Cords

Each Extreme Networks 325 W AC PSU is shipped with a 110 V AC UL Listed power cord.

All power supply cords provided by Extreme Networks are designed for use in the United States and
Canada only. Power supply cords for use outside of North America are typically provided by a
third-party distribution center and must meet the following requirements:

●

Power supply cords must be agency certified for country of use.

●

Power supply cords must contain an IEC 320 C13 connector for insertion into the IEC 320 C14
receptacle on the PSU.

●

Power supply cords must contain an appropriately rated and approved wall plug applicable to the
country of installation.

●

Power supply cords must be less than 5 m long.

●

Wire size must be a minimum of 18 AWG (0.82 mm

2

) copper-stranded.

WARNING!

Make sure that the source outlet is properly grounded before plugging the AC power cord into the Extreme Networks
325 W AC PSU.

Fuse

The Extreme Networks 325 W AC PSU line is fused. This is not a field operator replaceable fuse. In the
event of failure, immediately return the Extreme Networks 325 W AC PSU for a complete replacement.

WARNING!

Field operators must not attempt to configure or replace fuses in Extreme Networks 325 W AC PSUs! In the event of
failure, immediately return the defective Extreme Networks 325 W AC PSU for a complete replacement.

Specifications

The 325 W AC PSU functions from 90 V to 264 V and 47 Hz to 63 Hz AC Input. The software
determines the maximum available power required for the switch and enables the modules accordingly.

«
...
169
170
171
172
173
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: Ubiquiti Страницы: 24

Бренд: Ubiquiti Страницы: 13

Бренд: Ubisys Страницы: 2

Crouse-Hinds CEAG KO

Бренд: Cooper Страницы: 12

Бренд: Linksys Страницы: 3

Бренд: IOGear Страницы: 1

Бренд: XtendLan Страницы: 24

Бренд: ATEN Страницы: 2

Бренд: 3onedata Страницы: 2

Бренд: Radware Страницы: 4

Бренд: Santon Страницы: 16

Бренд: Led Control Страницы: 22

Бренд: Lutron Electronics Страницы: 2

IP-Watcher 2x2 Digital PoE

Бренд: W&T Страницы: 79

Бренд: Tripp Lite Страницы: 12

920-9B210-00FN-0D0

Бренд: Nvidia Страницы: 59

Бренд: Eaton Страницы: 2

Бренд: PABX Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды