manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

 

Table of Contents

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

6

Rack-Mounting the BlackDiamond 8806/12804 Chassis ............................................................110

Grounding the BlackDiamond 8806/12804 Chassis ...................................................................112

Initial Management Access ......................................................................................................113

Chapter 8: Installing the BlackDiamond 12802 Chassis................................................................. 115

Unpacking the BlackDiamond 12802 Chassis............................................................................115

Rack-Mounting the BlackDiamond 12802 Chassis .....................................................................117

Required Tools and Equipment...........................................................................................117
Front-Mounting a BlackDiamond 12802 Chassis ..................................................................117
Mid-Mounting a BlackDiamond 12802 Chassis ....................................................................118

Grounding the BlackDiamond 12802 Chassis ............................................................................119

Initial Management Access ......................................................................................................120

Chapter 9: Installing a BlackDiamond 10808 Chassis ................................................................... 121

Safety Information ..................................................................................................................121

Required Tools and Resources..................................................................................................122

Unpacking the Chassis and Preparing the Rack..........................................................................122

Checking the Shipping Status Indicators .............................................................................122
Removing the Accessories Box............................................................................................124
Removing the Carton from the Chassis ................................................................................126

Installing the Chassis ..............................................................................................................128

Standard Rack Installation .................................................................................................129
Mid-Mount Rack Installation ..............................................................................................132

Grounding the BlackDiamond 10808 Chassis ............................................................................134

Initial Management Access ......................................................................................................136

Chapter 10: Extreme Networks Power Supply Units for BlackDiamond Switches.............................. 137

Safety ....................................................................................................................................137

BlackDiamond PSU Compatibility .............................................................................................138

Extreme Networks 1200 W DC PSU ..........................................................................................139

Minimum Software Required ..............................................................................................139
Pre-Installation Requirements ............................................................................................140
Installing the DC Wiring .....................................................................................................140
Installing an Extreme Networks 1200 W DC PSU .................................................................141
Removing an Extreme Networks 1200 W DC PSU.................................................................144

Front Panel LEDs ........................................................................................................145

Extreme Networks 700/1200 W AC PSU ...................................................................................146

Pre-Installation Requirements ............................................................................................146
Installing an Extreme Networks 700/1200 W AC PSU...........................................................147
Removing an Extreme Networks 700/1200 W AC PSU..........................................................149
Front Panel LEDs ..............................................................................................................150

Power Supply Cords.....................................................................................................150
Fuse ..........................................................................................................................151

Specifications ...................................................................................................................151

Extreme Networks 600/900 W AC PSU .....................................................................................152

Minimum Software Required ..............................................................................................153
Pre-Installation Requirements ............................................................................................153
Installing an Extreme Networks 600/900 W AC PSU.............................................................154
Removing or Replacing an Extreme Networks 600/900 W AC PSU .........................................155

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

ABLE 6 Series Installation & Maintenance Instructions preview
6 Series
Бренд: ABLE Страницы: 5
D-Link DI-707 User Manual preview
DI-707
Бренд: D-Link Страницы: 36
D-Link DES-1018P User Manual preview
DES-1018P
Бренд: D-Link Страницы: 14
Magnetrol C29 Installation And Operating Manual preview
C29
Бренд: Magnetrol Страницы: 24
Xenteq PTS Series Instruction Manual preview
PTS Series
Бренд: Xenteq Страницы: 22
Vector MZ3-FA-V01 Manual preview
MZ3-FA-V01
Бренд: Vector Страницы: 6
K-Dyne OMP L80-P Manual preview
OMP L80-P
Бренд: K-Dyne Страницы: 10
Inline MSV0502 Operation Manual preview
MSV0502
Бренд: Inline Страницы: 26
LONG-JOIN JL-403C Manual preview
JL-403C
Бренд: LONG-JOIN Страницы: 2
Tripp Lite B310-701-4K Owner'S Manual preview
B310-701-4K
Бренд: Tripp Lite Страницы: 80
Edge-Core AS7326-56X Quick Start Manual preview
AS7326-56X
Бренд: Edge-Core Страницы: 9
DAB ESC plus 3M Instruction For Installation And Maintenance preview
ESC plus 3M
Бренд: DAB Страницы: 56
ATEN CS1922M User Manual preview
CS1922M
Бренд: ATEN Страницы: 17
PKP PSA10 Instruction Manual preview
PSA10
Бренд: PKP Страницы: 11
Eaton NZM3-XTVD-HS Instruction Leaflet preview
NZM3-XTVD-HS
Бренд: Eaton Страницы: 5
Intel Express 550F User Manual preview
Express 550F
Бренд: Intel Страницы: 162
SICK MSL Series Operating Instructions Manual preview
MSL Series
Бренд: SICK Страницы: 299
Veris Industries Hawkeye H950 Installation Manual preview
Hawkeye H950
Бренд: Veris Industries Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды