Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 424

background image

BlackDiamond 8800 Modules

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

56

MSM LEDs

Table 5

describes the LED activity on the MSM-G8X and MSM-48.

NOTE

The LEDs on the management Ethernet port are not labeled. The LED on the right is the link LED, and the one on
the left is the activity LED.

NOTE

The data port LEDs on the MSM-G8X operate the same as the port status LEDs on the G24X I/O module.

I/O Modules

This section describes the three different series of BlackDiamond 8800 I/O modules available for use in
a BlackDiamond 8800 series switch: the BlackDiamond 8800 original series I/O modules, the
BlackDiamond 8800 a-series I/O modules, and the BlackDiamond 8800 e-series I/O modules.

No configuration information is stored on the I/O modules; all configuration information is stored on
the MSM(s).

When a BlackDiamond 8800 series switch is powered on, the software generates a default configuration
for any slots that contain I/O modules. The default configuration allows the I/O module ports to

Table 5: MSM-G8X and MSM-48 LEDs

LED

Color

Indicates

SYS/STA

Green blinking

Normal operation is occurring.

Amber blinking

The status LED flashes amber while diagnostic tests are running on
the module. If a diagnostic test fails, the status LED becomes solid
amber. The LED resets if the diagnostics are terminated. The LED
returns to flashing amber if another diagnostic test is started.

Amber

Diagnostic failure has occurred.

Off

Switch is not receiving power.

MSTR/DIAG

Green

Module is operating as primary MSM.

Amber

Module is operating as backup (secondary) MSM.

Green blinking

Power-on self-test (POST) is running.

Off

Normal operation for diagnostics.

ERR

Amber

A critical software error has been logged since power-up.

Off

Normal operation is occurring.

ENV

Green

Environment (temperature, fan, power supply) is operating properly.

Amber

Environmental failure has occurred.

Link on MSTR
Ethernet port

Green

Link is up.

Off

Link is down.

Activity on MSTR

Amber

Packet activity is occurring.

«
...
54
55
56
57
58
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

RackSwitch G8264

Бренд: IBM Страницы: 20

Flex System FC3171

Бренд: IBM Страницы: 64

Бренд: Ultra Страницы: 20

Бренд: hager Страницы: 2

LMP-1204G-SFP Series

Бренд: ANTAIRA Страницы: 20

Бренд: Eaton Страницы: 2

Hi-Speed USB 2.0 Hub

Бренд: Saitek Страницы: 14

Бренд: Zhuoyi Страницы: 2

Бренд: Extron electronics Страницы: 1

Бренд: M-E Страницы: 36

Бренд: Kramer Страницы: 46

Бренд: Black Box Страницы: 50

SECURVIEW SV-7020

Бренд: CrimeStopper Страницы: 1

Бренд: LevelOne Страницы: 40

Бренд: odot Страницы: 15

Бренд: AVCOMM Страницы: 2

Бренд: Kramer Страницы: 10

Бренд: TRENDnet Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды