Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 109

Страница: 109 / 424

Pre-installation Requirements

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

109

Pre-installation Requirements

The following tools, equipment, and resources are required for installing the BlackDiamond 8806/12804
chassis:

●

ESD-preventive wrist strap (provided)

●

19-inch helper bracket (provided)

●

For installing the chassis in a mid-mount position in the rack:

■

Optional BlackDiamond 8806/12804 mid-mount kit, part number 65046. Order this kit separately
from the chassis.

■

#2 Phillips screwdriver

●

Rack-mount screws appropriate for your organization’s rack system, as follows:

■

4 screws to attach the helper bracket

■

12 screws to secure the BlackDiamond 8810 chassis in the rack

The screw size will vary based on your organization’s rack system; screws are not provided.

●

Screwdriver appropriate for the rack-mounting screws you will use

The screwdriver size will vary based on the requirements of your organization’s rack system.

Attaching the BlackDiamond 8806/12804 Mid-Mount
Brackets

To install the BlackDiamond 8806/12804 switch in a mid-mount position in the rack, attach the optional
BlackDiamond 8806/12804 mid-mount brackets.

To attach the BlackDiamond 8806/12804 mid-mount brackets:

Place the empty BlackDiamond 8806/12804 chassis in an upright position on a secure flat surface.

CAUTION

The BlackDiamond 8806/12804 chassis weighs almost 65 pounds. Proper lifting and moving of the chassis requires
two people.

Determine the locations for the mid-mount brackets.

NOTE

Each side of the chassis has two sets of mounting holes to provide two positions for attaching the mid-mount
brackets.

Identify the left and right brackets.

Each mid-mount bracket is clearly marked for placement on either the right or left side, as viewed
from the front of the chassis.

On each side of the chassis, attach the appropriate mid-mount bracket using the eight screws
provided in the kit (see

Figure 58

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды