Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 424

background image

Extreme Networks 600/900 W AC PSU

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

153

NOTE

The Extreme Networks 600/900 W AC PSU can be used in conjunction with an Extreme Networks 700W/1200W AC
PSU in the same BlackDiamond 8806 system.

NOTE

Extreme Networks does not recommend using the 600W/900W AC PSU in conjunction with an Extreme Networks
1200W DC PSU in the same BlackDiamond 8806 system.

WARNING!

Field operators must not attempt to open the 600W/900W AC PSU enclosure for any reason; the PSU does not
contain user-serviceable parts. In the event of failure, return the defective 600W/900W AC PSU to Extreme
Networks for repair or replacement.

Minimum Software Required

The MSM running in your BlackDiamond 8806 switch requires ExtremeXOS version 11.6.1 (or later) in
order to recognize an Extreme Networks 600/900 W AC PSU. In ExtremeXOS releases 11.3.4, 11.4.2, and
11.5.1, the 600/900 W AC PSU is disabled on all chassis. In ExtremeXOS releases earlier than those, the
software does not recognize the 600/900 W AC PSU and the PSU will not be budgeted properly,
possibly resulting in PSU shutdown and/or chassis reboot.

Pre-Installation Requirements

WARNING!

Extreme Networks 600/900 W AC PSUs do not have switches for turning the unit on and off. Remove the wall plug
from the electrical outlet to disconnect the power to an Extreme Networks 600/900 W AC PSU. Make sure that this
connection is easily accessible.

When the PSU is outside of the chassis (not installed), do not plug the PSU into an electrical outlet. Plugging an
uninstalled PSU into an electrical outlet exposes you to a hazardous energy and is a potential fire hazard.

You need the following tools and equipment before installing or removing an Extreme Networks
600/900 W AC PSU(s):

●

ESD-preventive wrist strap

●

Power supply cord (110 V AC, 220 V AC, or applicable to country of use)

A power cord for use in the United States is provided with each PSU. For use outside of the United
States, this PSU requires a power supply cord set certified for country of use. See input specifications
under

AC PS Model #41050 (600/900 W AC PSU)

on page 395

.

●

Thermal protective gloves (required for removal; the PSU is hot to the touch)

«
...
151
152
153
154
155
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: X10 Страницы: 20

VNLW-P-1001-MV-N-V

Бренд: Greengate Страницы: 2

HD Flash 4 KD-SW4x1

Бренд: Key Digital Страницы: 12

Бренд: protech Страницы: 4

Бренд: NTI Страницы: 15

Бренд: Eaton Страницы: 2

Бренд: IPGARD Страницы: 2

Guard Master 440N-Z2NRS1A

Бренд: Allen-Bradley Страницы: 4

Бренд: FS Страницы: 43

Бренд: Guralp Systems Страницы: 22

Бренд: Lantech Страницы: 29

Бренд: TRENDnet Страницы: 2

EdgeSwitch 8 150W

Бренд: Ubiquiti Страницы: 28

Бренд: axing Страницы: 4

Бренд: Intellinet Страницы: 48

Бренд: PTN Страницы: 44

Thunder series 930

Бренд: A10 Страницы: 44

Бренд: Raritan Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды