manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

BlackDiamond 12800 Series Modules

 

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

70

NOTE

The BlackDiamond R-series modules must be used together to take advantage of the higher feature set and scale. 
The ExtremeXOS software recognizes the MSM type installed in your BlackDiamond 12800 series switch and only 
allows use of compatible I/O modules from the same series. An error message is displayed if you attempt to mix 
modules. 

BlackDiamond 12800 Series MSMs

The BlackDiamond 12800 series management system modules (MSMs) are the MSM-5 module and the 
MSM-5R module. These MSMs provide the active switching fabric and CPU control subsystem for the 
switch. The BlackDiamond 12802 chassis has one dedicated MSM slot; the BlackDiamond 12804 chassis 
has two dedicated MSM slots. One MSM is required for switch operation; however, adding a second 
MSM to a BlackDiamond 12804 chassis increases system availability through redundancy. Each MSM 
provides 192 Gbps of switching throughput through three ASICs. Each module also contains a 
temperature sensor, nonvolatile random-access memory (NVRAM), and a real-time clock.

The MSM-5 and MSM-5R modules support different sizes of Ternary Content Addressable Memory 
(TCAM). The MSM-5R has more memory available for routing tables, learned MAC addresses, and 
access control lists (ACLs). For specific details about memory allocation, refer to the data sheet for each 
module. 

CAUTION

You must use compatible MSMs and I/O modules from either the BlackDiamond 12800 series or the 12800 R-
series of modules. Do not attempt to mix MSMs from the two different series. The ExtremeXOS software recognizes 
the MSM type installed in your BlackDiamond 12800 series switch and only allows use of a second MSM of the 
same type and compatible I/O modules from the same series. An error message is displayed if you attempt to mix 
module series.

NOTE

In the BlackDiamond 12804 switch, installed MSMs require ExtremeXOS 11.4.1 or later. 

In the BlackDiamond 12802 switch, MSMs must be running ExtremeXOS 12.0.1 or later. You must upgrade the 
MSM before you deploy the BlackDiamond 12802 switch in your network. A BlackDiamond 12802 switch running 
software earlier than version 12.0.1 will not be fully operational.

To upgrade the software in your BlackDiamond 12802 switch, access the latest 12.0.1 image at the Extreme 
Networks support website and follow the upgrade instructions in the 

ExtremeXOS 12.0 Release Notes

.

NOTE

The MSM slot in the BlackDiamond 12802 switch is labeled MSM on the front panel. The ExtremeXOS software 
refers to this MSM as MSM-A in all related displays and command output.

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

D-Link DUB-H4 - Hub - USB Installation Manual preview
DUB-H4 - Hub - USB
Бренд: D-Link Страницы: 4
D-Link DSS-16+ Quick Install Manual preview
DSS-16+
Бренд: D-Link Страницы: 2
GAIM Compact Troubleshooting preview
Compact
Бренд: GAIM Страницы: 2
Dataprobe iBoot PoE-P General Description Manual preview
iBoot PoE-P
Бренд: Dataprobe Страницы: 31
IBM ThinkPad 600 Product Overview preview
ThinkPad 600
Бренд: IBM Страницы: 13
IBM Flex System EN2092 Quick Start Manual preview
Flex System EN2092
Бренд: IBM Страницы: 2
3onedata TNS5500D Series Quick Start Manual preview
TNS5500D Series
Бренд: 3onedata Страницы: 5
3onedata IPS7112G-4GS-8GPOE Quick Installation Manual preview
IPS7112G-4GS-8GPOE
Бренд: 3onedata Страницы: 3
DANLERS CESF PIR Installation Notes preview
CESF PIR
Бренд: DANLERS Страницы: 2
Fairchild FSD200 Manual preview
FSD200
Бренд: Fairchild Страницы: 14
FELA SWITCH CASAMBI Operation And Installation Manual preview
SWITCH CASAMBI
Бренд: FELA Страницы: 13
Ubiquiti ES-24-250W Quick Start Manual preview
ES-24-250W
Бренд: Ubiquiti Страницы: 24
Ubiquiti USW-24 User Manual preview
USW-24
Бренд: Ubiquiti Страницы: 13
Ubisys ZIGBEE S2(-R) Quick Start Manual preview
ZIGBEE S2(-R)
Бренд: Ubisys Страницы: 2
BeeSecure BEE-REPEATER Quick Start Manual preview
BEE-REPEATER
Бренд: BeeSecure Страницы: 35
Lindy 32351 Manual preview
32351
Бренд: Lindy Страницы: 70
Eaton RMQ-Titan M30 Series Instruction Leaflet preview
RMQ-Titan M30 Series
Бренд: Eaton Страницы: 4
V7 MPEGS24 User Manual preview
MPEGS24
Бренд: V7 Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды