Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 424

background image

Summit X250e Series Switches

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

249

The rear panel on the Summit X250e-48p switch includes:

●

Management port

■

Used to connect the system to a parallel management network for administration.

OR

■

Used to connect an Ethernet cable directly from your laptop to the management port to view and
locally manage the switch configurations.

●

Two LEDs for the management port, located in the bottom corners of the port.

●

Two high-performance stacking ports with associated LEDs

●

Redundant power input connector for optional connection to an EPS-C chassis, which can hold up to
three EPS-600LS external power modules. The PoE capability of the Summit X250e-48p switch varies
depending on the number of external power modules in use. For complete details, see

“EPS-600LS

External Power Module” on page 328

. The connecting redundant power supply cable is shipped

with the EPS-C chassis.

●

AC power socket

The switch automatically adjusts to the supply voltage. The power supply operates from 100 VAC to
240 VAC.

Summit X250e-48p Power Supplies

The Summit X250e-48p switch is powered by both an internal power supply and an optional external
redundant power supply system.

Internal Power Supply.

The internal Summit X250e-48p internal power supply is capable of 370 W of PoE

power. It supplies 15.4 W to each port for a 24-port configuration and 7.7 W to each port for a 48-port
configuration or any combination of ports where total PoE power does not exceed 370 watts. If the total
system demands exceed this power limit, you can specify one of the following:

●

Port priorities to identify which ports should be ranked higher when allocating power

●

Port disconnect precedence to specify the method of shutting off ports when not enough PoE power
is available

NOTE

A full discussion of these concepts can be found in the

ExtremeXOS 12.0 Concepts Guide

, Power over Ethernet

section.

External Power Supplies.

The EPS-600LS External Power Module provides optional redundant power for

the Summit X250e-48p switch. Through the redundant power input connector on the rear panel, the
switch can be powered by one, two, or three external power modules installed in the EPS-C External
Power Supply Chassis.

The PoE capability of the Summit X250e-48p varies depending on the number of external power
modules in use.

Table 28

summarizes the PoE power behavior for the Summit X250e-48p switch based

on the number of power supply modules in use.

«
...
247
248
249
250
251
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: GE Страницы: 36

Бренд: GE Страницы: 8

Бренд: Dataprobe Страницы: 31

Бренд: IBM Страницы: 13

Flex System EN2092

Бренд: IBM Страницы: 2

Draco major K474-U8/C8

Бренд: Ihse Страницы: 167

Бренд: steute Страницы: 10

Бренд: PNI Страницы: 92

Бренд: Racal Instruments Страницы: 33

Бренд: Cable Electronics Страницы: 12

Signal Distribution Box SDB45

Бренд: Audiovox Страницы: 12

Бренд: HighSecLabs Страницы: 10

Vertical Horizon VH-2402-L3

Бренд: Enterasys Страницы: 201

Бренд: Epcom Страницы: 2

Бренд: Rosewill Страницы: 3

Бренд: Magnetrol Страницы: 32

Бренд: Quintum Страницы: 125

Tuffset 200302F

Бренд: VXI Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды