Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 262

Страница: 262 / 424

Summit Family of Switches

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

262

The front panel on the Summit X450a-24x switch includes:

●

LEDs—For a description of the LEDs and their behavior, see

“Summit X450, X450a, and X450e Series

Switch LEDs” on page 276

●

Stack number indicator—Numeric indicator of the position of this switch in a stacked configuration.

●

Combination ports—Four combination ports that provide 10/100/1000 BASE-T or mini-GBIC
connectivity for 4 Gbps of fiber or copper connectivity.

●

Mini-GBIC ports—20 mini-GBIC ports that deliver high-density fiber connectivity in 1.75-inch (1U)
form factor.

●

Console port—Serial port used to connect a terminal and perform local management.

Summit X450a-24x Switch Rear Panel

Figure 184

shows the rear panel of the Summit X450a-24x switch.

Figure 184: Summit X450a-24x switch rear panel

The rear panel on the Summit X450a-24x switch includes:

●

Slot for a Summit option card

■

Summit XGM2-2xn option card, which allows you to add up to two 10 Gigabit XENPAK modules

■

Summit XGM2-2xf option card, which allows you to add up to two 10 Gigabit XFP modules

NOTE

For information regarding these compatible Summit option cards, see

“Summit XGM2-2xn Option Card” on

page 297

“Summit XGM2-2xf Option Card” on page 302

●

Management port

■

Used to connect the system into a parallel management network for administration.

■

Used to connect an Ethernet cable directly from your laptop into the management port to view
and locally manage the switch configurations.

●

Two LEDs for the management port, located in the bottom corners of the port.

●

Two high-performance stacking ports

SH_031

10 Gigabit

uplink option

Management port

10 Gigabit

stacking ports

Power socket

External power

supply connection

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды