Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 424

background image

Installing a BlackDiamond 8800 or 12800 Series Module

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

177

8

Using a #2 Phillips screwdriver, lock the module into place in one of the following ways (

Figure 106

):

●

If the captive screw on each handle has a yellow band around the head of the screw, turn the
screw on each injector/ejector handle clockwise and

completely

down. When the screw is

completely tightened, the yellow band around the captive screw is completely hidden.

CAUTION

Be careful to avoid over-torquing and stripping the screw heads.

●

If the captive screw on each handle has a red line on the head (see

Figure 107

), turn each captive

screw one-quarter turn (90 degrees) clockwise. When the module is correctly locked, the red line
on the captive screw in each injector/ejector handle is in a vertical position.

CAUTION

Be sure to turn each captive screw

only

90 degrees or one-quarter turn clockwise. Tightening the captive screws

beyond 90 degrees will damage the injector/ejector handles on the modules.

Figure 106: Locking the module into place

Figure 107: Captive screw with red line

9

Store the module packaging for future use.

NOTE

Leave the ESD-preventive wrist strap permanently connected to the chassis so that the strap is always available
when you need to handle ESD-sensitive components.

EX_125

EX_162

«
...
175
176
177
178
179
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

xStack DGS-3420 Series

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 29

Бренд: D-Link Страницы: 454

Бренд: D-Link Страницы: 502

Бренд: D-Link Страницы: 244

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 37

Бренд: D-Link Страницы: 28

BNI IOL-314-S52-P012

Бренд: Balluff Страницы: 22

S5560S-EI Series

Бренд: H3C Страницы: 37

OfficeConnect WX4400

Бренд: 3Com Страницы: 528

Бренд: CalDigit Страницы: 13

Бренд: Sangamo Страницы: 2

EdgeLens INT10G8SR56

Бренд: Garland Страницы: 76

T0-4 SE2 Series

Бренд: Eaton Страницы: 2

Бренд: SELS Страницы: 2

Бренд: Magnum Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды