Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 247 | Manualshive

Страница: 247 / 424

background image

Summit X250e Series Switches

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

247

Figure 172: Summit X250e-48t switch rear panel

The rear panel on the Summit X250a-48t switch includes:

●

Management port

■

Used to connect the system into a parallel management network for administration.

OR

■

Used to connect an Ethernet cable directly from your laptop into the management port to view
and locally manage the switch configurations.

●

Two LEDs for the management port, located in the bottom corners of the port.

●

Two high-performance stacking ports with associated LEDs

●

Redundant power input connector for an optional, redundant EPS-500 Power Supply unit. (See

“EPS-160 External Power Module (with EPS-T)” on page 309

for complete details.) The connecting

redundant power supply cable is shipped with the EPS-500 unit.

●

AC Power Socket

The switch automatically adjusts to the supply voltage. The power supply operates from 100 VAC to
240 VAC.

Summit X250e-48p Switch

The Summit X250e-48p switch is a compact unit 1.75 inches high (1 U) that includes the following:

●

Forty-eight fixed 10/100BASE-T PoE ports (ports 1–48) that deliver high-density copper connectivity
and a full 15.4 Watts of PoE per port when used with the EPS-600LS External Power Module.

●

Two combination ports (ports 49–50) that provide 10/100/1000 BASE-T PoE or mini-GBIC
connectivity for 2 Gbps of copper or fiber connectivity

NOTE

For information about mini-GBICs, see

“Mini-GBIC Interfaces” on page 338

.

●

Two high-performance stacking ports with associated LEDs

●

Redundant power input connector for use with one or more EPS-600LS External Power Modules
(Model No. 10913) installed in an EPS-C chassis (Model No. 10912). The PoE capability of the
Summit X250e-48p switch varies depending on the number of external power modules in use. For
complete details, see

“EPS-600LS External Power Module” on page 328

.

SH_045

Stacking ports

Management port

Power socket

External power

supply connection

«
...
245
246
247
248
249
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

IPS7110-2GC-8POE

Бренд: 3One data Страницы: 3

Бренд: ABB Страницы: 10

Бренд: Key Digital Страницы: 20

Бренд: Versitron Страницы: 46

Бренд: Ortech Страницы: 3

Бренд: TRENDnet Страницы: 2

Бренд: Angustos Страницы: 15

Бренд: Rosewill Страницы: 3

Бренд: Cabletron Systems Страницы: 12

SW-UNM-8FE1GC-8POE

Бренд: MO-EL Страницы: 9

ECRAFT SMART HOME Series

Бренд: Globalmediapro Страницы: 4

Orion XC OXS-XC008-FS

Бренд: Rose electronics Страницы: 132

Бренд: GE Страницы: 158

Бренд: JVC Страницы: 2

Бренд: JVC Страницы: 26

Бренд: JVC Страницы: 34

Бренд: JVC Страницы: 28

Бренд: JVC Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды