Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 218

Страница: 218 / 424

Replacing a BlackDiamond 12804 or 8800 Series Fan Tray

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

218

Figure 143: Removing the fan tray from the BlackDiamond 8810 switch

Figure 144: Removing the fan tray from the BlackDiamond 8806/12804 switch

Use the fan tray handle to pull the fan tray half-way out from the fan tray slot. This action
disconnects the fan tray from the switch power.

Wait for the fan blades to stop turning before continuing with this procedure.

WARNING!

Be sure that all fan blade motion has ceased before continuing to remove the fan tray.

Support the bottom of the fan tray with your free hand as you use the handle to slide the fan tray
completely out from the fan tray slot.

ASP031A

Fan Tray
Handle

Fan Tray
Captive
Screws (x2)

EX_114

Fan

tray

andle

Fan

tray

captive
screws

(x2)

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды