Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 424

background image

Extreme Networks Power Supply Units for BlackDiamond Switches

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

138

WARNING!

Field operators must not attempt to open the PSU enclosure for any reason; the PSU does not contain
user-serviceable parts. In the event of failure, return the defective PSU to Extreme Networks for repair or
replacement.

BlackDiamond PSU Compatibility

The BlackDiamond power supply units are intended for use in specific BlackDiamond switches only.

Table 17

lists the BlackDiamond switches and their compatible power supply units.

NOTE

When a combination of 600/900 W AC PSUs and 700/1200 W AC PSUs are powered on in the same BlackDiamond
8806 chassis, all PSUs will be budgeted down to the lower-powered 600/900 W AC output values to avoid PSU
shutdown due to over-current. Refer to their respective sections for complete details.

NOTE

The MSM running in your BlackDiamond 8806 switch requires ExtremeXOS version 11.6.1 (or later) to recognize an
Extreme Networks 600/900 W AC PSU. In ExtremeXOS releases 11.3.4, 11.4.2, and 11.5.1, the 600/900 W AC
PSU is disabled on all chassis. In ExtremeXOS releases before those, the software does not recognize the 600/900
W AC PSU and the PSU will not be budgeted properly, possibly resulting in PSU shutdown and/or chassis reboot.

Table 17: PSU compatibility in the BlackDiamond switches

BlackDiamond Switch

Compatible PSU

Compatibility Notes

BlackDiamond 8806

600W/ 900W AC PSU

AND/OR

700W/ 1200W AC PSU

OR

1200W DC PSU

The 700/1200 W AC PSU can be used in conjunction
with a 600/900 W AC PSU in the same BlackDiamond
8806 system only.

Extreme Networks

does not

recommended using the

600/900 W AC PSU or the 700/1200 W AC PSU in
conjunction with a 1200W DC PSU.

BlackDiamond 8810

700W/ 1200W AC PSU

OR

1200W DC PSU

Extreme Networks

does not

recommended using the

700/1200 W AC PSU in conjunction with a
1200W DC PSU.

BlackDiamond 10808

700W/ 1200W AC PSU

OR

1200W DC PSU

Extreme Networks

does not

recommended using the

700/1200 W AC PSU in conjunction with a
1200W DC PSU.

BlackDiamond 12804

700W/ 1200W AC PSU

OR

1200W DC PSU

Extreme Networks

does not

recommended using the

700/1200 W AC PSU in conjunction with a
1200W DC PSU.

BlackDiamond 12802

325 W AC PSU, Model
# 65021

OR

325 W DC PSU, Model
# 65022

Extreme Networks

does not

recommended using the

325 W AC PSU in conjunction with the 325 W DC PSU.

«
...
136
137
138
139
140
...
»

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Бренд: D-Link Страницы: 36

Switch 4500 Family

Бренд: 3Com Страницы: 742

Бренд: 3Com Страницы: 940

Бренд: 3Com Страницы: 43

OfficeConnect WX1200

Бренд: 3Com Страницы: 646

Бренд: Lantronix Страницы: 40

Бренд: Lantronix Страницы: 2

SISTP1040-551-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 2

SISPM1040-3 L Series

Бренд: Lantronix Страницы: 2

SISPM1040 L3 Series

Бренд: Lantronix Страницы: 36

SecureLinx Spider

Бренд: Lantronix Страницы: 18

Бренд: Lantronix Страницы: 8

Бренд: Lantronix Страницы: 6

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 272

Xpress-Pro SW 52000

Бренд: Lantronix Страницы: 8

Бренд: Attwood Страницы: 2

Бренд: LevelOne Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды