Extreme Networks BlackDiamond 10808 Скачать руководство пользователя страница 101

Страница: 101 / 424

Rack Mounting the BlackDiamond 8810 Chassis

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

101

Rack Mounting the BlackDiamond 8810 Chassis

To install the BlackDiamond 8810 chassis in a rack:

Locate the 19-inch helper bracket that is shipped with the chassis.

Identify the rack location where the chassis will be installed.

Using four rack-mounting screws, attach the helper bracket to the system rack immediately below
the chassis location as shown in

Figure 51

You must provide the screws for attaching the helper bracket.

Figure 51: Attaching the helper bracket to the system rack

Lift the back of the empty chassis onto the helper bracket.

Slowly guide the chassis into the system rack until the mounting brackets are flush against the rack
uprights.

EX_086A

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Результаты поиска

Содержание BlackDiamond 10808

Отзывы:

Похожие инструкции для BlackDiamond 10808

Бренды по названию

Популярные бренды