manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

 

Table of Contents

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

8

Chapter 13: BlackDiamond Cable Management ............................................................................. 197

About BlackDiamond Cable Management ..................................................................................197

Installing the BlackDiamond 10808 Cable Manager ...................................................................197

Using the Cable Holders and Cable Clips ...................................................................................202

Connecting Cable Holders ..................................................................................................203
Connecting Cable Clips ......................................................................................................204

Part 5: BlackDiamond Maintenance Procedures

Chapter 14: Replacing the BlackDiamond 12802 PSU/Fan Controller and Fan Tray ......................... 209

Safety Information ..................................................................................................................209

Pre-installation Requirements ..................................................................................................209

Replacing the BlackDiamond 12802 Fan Tray ...........................................................................209

Replacing a BlackDiamond PSU/Fan Controller ..........................................................................211

Chapter 15: Replacing a BlackDiamond 8800 Series/BlackDiamond 12804 PSU/Fan Controller ...... 213

Pre-Installation Requirements ..................................................................................................213

Removing a BlackDiamond 8800/12804 PSU/Fan Controller ......................................................213

Installing a BlackDiamond 8800/12804 Spare PSU/Fan Controller..............................................216

Chapter 16: Replacing a BlackDiamond 12804 or 8800 Series Fan Tray........................................ 217

Pre-Installation Requirements ..................................................................................................217

Removing the Fan Tray ............................................................................................................217

Installing the BlackDiamond 8810 Spare Fan Tray .....................................................................219

Chapter 17: Replacing the BlackDiamond 10808 Switch Fan Tray, Air Filter, and 
Power Supply Controller .............................................................................................................. 221

Replacing a BlackDiamond 10808 Switch Fan Tray ...................................................................221

Removing the Fan Tray ......................................................................................................221
Installing the Replacement Fan Tray ...................................................................................222

Replacing the BlackDiamond 10808 Air Filter ...........................................................................223

Replacing the BlackDiamond 10808 Power Supply Controller .....................................................224

Pre-Installation Requirements ............................................................................................225
Removing a Power Supply Controller ...................................................................................225
Installing a Power Supply Controller ....................................................................................226
Verifying a Successful Installation.......................................................................................226

Chapter 18: Repacking a BlackDiamond Chassis........................................................................... 227

Safety Information ..................................................................................................................227

Repacking the BlackDiamond 8810 Chassis ..............................................................................228

Repacking the BlackDiamond 8806/12804 Chassis ...................................................................231

Repacking the BlackDiamond 12802 Chassis ............................................................................234

Repacking the BlackDiamond 10808 Chassis ............................................................................235

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Hama 78499 Operating Instructions Manual preview
78499
Бренд: Hama Страницы: 10
Hama 11467 Operating Instruction preview
11467
Бренд: Hama Страницы: 14
Oase Underwater Switch 24V DC/DMX/02 Operating Instructions Manual preview
Underwater Switch 24V DC/DMX/02
Бренд: Oase Страницы: 40
ATZ HDMI-161SM Manual preview
HDMI-161SM
Бренд: ATZ Страницы: 8
Gefen EXT-DVIKVM-441DL User Manual preview
EXT-DVIKVM-441DL
Бренд: Gefen Страницы: 32
UNICOM SmartGST-2600M Specifications preview
SmartGST-2600M
Бренд: UNICOM Страницы: 1
Xantech 680-10 Installation Instructions preview
680-10
Бренд: Xantech Страницы: 4
Extron electronics 60-1021-01 User Manual preview
60-1021-01
Бренд: Extron electronics Страницы: 137
Raritan PC-Share Installation And Operation preview
PC-Share
Бренд: Raritan Страницы: 4
Cumberland PowerTrak Installation preview
PowerTrak
Бренд: Cumberland Страницы: 2
Lindy 32320 User Manual preview
32320
Бренд: Lindy Страницы: 12
Kensence S-Mix-Pro 18*18 Operation Manual preview
S-Mix-Pro 18*18
Бренд: Kensence Страницы: 24
PowerShield PSMBSR10K Quick Manual preview
PSMBSR10K
Бренд: PowerShield Страницы: 2
NETGEAR GSM7352S - ProSafe Switch - Stackable User Manual preview
GSM7352S - ProSafe Switch - Stackable
Бренд: NETGEAR Страницы: 628
KTI KCB-121 User Manual preview
KCB-121
Бренд: KTI Страницы: 16
NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart Switch Software Administration Manual preview
FS728TP - ProSafe 24 Port 10/100 Smart Switch
Бренд: NETGEAR Страницы: 261
Gigabyte SW008A Reference Manual preview
SW008A
Бренд: Gigabyte Страницы: 2
N-Tron 509FX Specification Sheet preview
509FX
Бренд: N-Tron Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды