manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

Table of Contents

 

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

7

Front Panel LEDs ..............................................................................................................156
Power Supply Cords...........................................................................................................156
Fuse ................................................................................................................................157
Specifications ...................................................................................................................157

Extreme Networks 325 W DC Power Supply ...............................................................................158

Minimum Software Required ..............................................................................................158
Pre-Installation Requirements ............................................................................................159
Installing the DC Wiring .....................................................................................................159
Installing an Extreme Networks 325 W DC PSU ...................................................................160
Removing an Extreme Networks 325 W DC PSU...................................................................163
LEDs................................................................................................................................164
Fuse ................................................................................................................................164
Specifications ...................................................................................................................164

Extreme Networks 325 W AC Power Supply ...............................................................................165

Pre-Installation Requirements ............................................................................................165
Installing an Extreme Networks 325 W AC PSU ...................................................................166
Installing Retaining Brackets and Connecting Power .............................................................168
Removing an Extreme Networks 325 W AC PSU...................................................................170
Front Panel LEDs ..............................................................................................................170
Power Supply Cords...........................................................................................................171
Fuse ................................................................................................................................171

Specifications.........................................................................................................................171

Chapter 11: Installing BlackDiamond Series Modules.................................................................... 173

Module Slot Assignments.........................................................................................................173

Distinguishing a BlackDiamond 8800 or 12800 MSM from an I/O Module ...................................174

Installing a BlackDiamond 8800 or 12800 Series Module ..........................................................175

Connecting and Disconnecting Cables on the 10G4Ca Module.....................................................178

Installing a BlackDiamond 10808 Series Module .......................................................................179

Installing a Backup MSM .........................................................................................................182

Verifying the Module Installation ..............................................................................................182

Displaying Slot Status Information ......................................................................................182

Removing a BlackDiamond 8800 or 12800 Series Module .........................................................183

Removing a BlackDiamond 10808 Series Module ......................................................................184

BlackDiamond Series Blank Front Panels ..................................................................................185

Installing a Blank Front Panel ............................................................................................185
Removing a Blank Front Panel............................................................................................186
Installing or Removing an External Compact Flash Memory Card ............................................188

Part 4: Installing BlackDiamond Switch Accessories

Chapter 12: BlackDiamond AC Power Cord Retaining Brackets ...................................................... 191

BlackDiamond 8810 AC Power Cord Retaining Bracket ..............................................................191

Installing the BlackDiamond 8810 AC Power Cord Retaining Bracket.....................................191
Disconnecting a BlackDiamond 8810 AC Power Cord ...........................................................193

BlackDiamond 8806/12804 AC Power Cord Retainer Channel ....................................................194

Pre-Installation Requirements ............................................................................................194
Installing the BlackDiamond 8806/12804 AC Power Cord Retainer Channel...........................194
Removing the BlackDiamond 8806/12804 AC Power Cord Retainer Channel ..........................196

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Keithley 3700 series Reference Manual preview
3700 series
Бренд: Keithley Страницы: 434
Hama 11800 Operating Instruction preview
11800
Бренд: Hama Страницы: 5
3Com SuperStack 3 4900 Datasheet preview
SuperStack 3 4900
Бренд: 3Com Страницы: 2
Cabletron Systems MMAC-Plus 9G426-02 Reference Manual preview
MMAC-Plus 9G426-02
Бренд: Cabletron Systems Страницы: 12
Cabletron Systems MMAC-Plus 9F310-02 Appendix preview
MMAC-Plus 9F310-02
Бренд: Cabletron Systems Страницы: 4
Cabletron Systems 9E423-36 Owner'S Manual preview
9E423-36
Бренд: Cabletron Systems Страницы: 16
cable matters 101065 Quick Start Manual preview
101065
Бренд: cable matters Страницы: 4
CableCreation CD0395 User Manual preview
CD0395
Бренд: CableCreation Страницы: 7
Cabletron Systems SmartSwitch 9A100 Installation And Setup Manual preview
SmartSwitch 9A100
Бренд: Cabletron Systems Страницы: 52
Cabletron Systems SmartSwitch 9W006 Quick Start Manual preview
SmartSwitch 9W006
Бренд: Cabletron Systems Страницы: 34
Cabletron Systems SmartSTACK ELS100-S24TX2M Management Manual preview
SmartSTACK ELS100-S24TX2M
Бренд: Cabletron Systems Страницы: 102
Cabletron Systems 9A426-01 Appendix preview
9A426-01
Бренд: Cabletron Systems Страницы: 24
Cabletron Systems SmartSwitch 9000 Appendix preview
SmartSwitch 9000
Бренд: Cabletron Systems Страницы: 14
Cabletron Systems MicroMMAC 22ES Reference Manual preview
MicroMMAC 22ES
Бренд: Cabletron Systems Страницы: 38
Aruba Instant On 1930 24G 4SFP/SFP+l Installation And Getting Started Manual preview
Instant On 1930 24G 4SFP/SFP+l
Бренд: Aruba Страницы: 48
IMC Networks iMcV-Giga-FiberLinX-II Operation Manual preview
iMcV-Giga-FiberLinX-II
Бренд: IMC Networks Страницы: 60
Audio Authority HMX-244 Installation And Operation Manual preview
HMX-244
Бренд: Audio Authority Страницы: 12
steute EX ZS 92 S 22 VD F Mounting And Wiring Instructions preview
EX ZS 92 S 22 VD F
Бренд: steute Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды