manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

Table of Contents

 

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

5

I/O Port LEDs......................................................................................................................74
GM-20T I/O Module ............................................................................................................74

GM-20T LEDs ...............................................................................................................75

GM-20XT and GM-20XTR I/O Modules ..................................................................................75

GM-20XT and GM-20XTR LEDs ......................................................................................76

XM-2X and XM-2XR I/O Modules ..........................................................................................76

XM-2X and XM-2XR LEDs ..............................................................................................77

Distinguishing a BlackDiamond 12800 Series MSM from an I/O Module ........................................77

Module Slot Assignments...........................................................................................................77

Chapter 5: BlackDiamond 10808 Series Modules ........................................................................... 79

About the BlackDiamond 10808 MSMs ......................................................................................79

MSM Activity ......................................................................................................................80
MSM LEDs .........................................................................................................................81

About the BlackDiamond 10808 I/O Modules ..............................................................................82

G60T Module .....................................................................................................................83

G60T LEDs...................................................................................................................83

G60X Module .....................................................................................................................84

Mini-GBIC Ports ............................................................................................................84
G60X LEDs...................................................................................................................85

G20X Module .....................................................................................................................85

Mini-GBIC Ports ............................................................................................................86
G20X LEDs...................................................................................................................86

10G6X Module ...................................................................................................................86

XENPAK Ports ..............................................................................................................87
10G6X LEDs.................................................................................................................87

10G2X Module ...................................................................................................................88

XENPAK Ports ..............................................................................................................88
10G2X LEDs.................................................................................................................89

10G2H Module ...................................................................................................................89

XENPAK Ports ..............................................................................................................90
Mini-GBIC Ports ............................................................................................................90
10G2H LEDs ................................................................................................................90

I/O Module LEDs .................................................................................................................91

Part 3: Installing BlackDiamond Switches and Modules

Chapter 6: Installing the BlackDiamond 8810 Chassis..................................................................... 95

Safety Information ....................................................................................................................95

Unpacking the BlackDiamond 8810 Chassis................................................................................96

Pre-Installation Requirements ....................................................................................................99

Attaching the BlackDiamond 8810 Mid-Mount Rack Brackets .....................................................100

Rack Mounting the BlackDiamond 8810 Chassis .......................................................................101

Grounding the BlackDiamond 8810 Chassis ..............................................................................103

Initial Management Access ......................................................................................................104

Chapter 7: Installing the BlackDiamond 8806 and BlackDiamond 12804 Chassis ........................... 105

Unpacking the BlackDiamond 8806/12804 Chassis...................................................................106

Pre-installation Requirements ..................................................................................................109

Attaching the BlackDiamond 8806/12804 Mid-Mount Brackets ..................................................109

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

Barco ScreenPRO-II Brochure & Specs preview
ScreenPRO-II
Бренд: Barco Страницы: 6
Gilat SkyEdge II-c Capricorn Pro 4 AC Series Installation Notes preview
SkyEdge II-c Capricorn Pro 4 AC Series
Бренд: Gilat Страницы: 2
Extron electronics MSW 4SV rs Specifications preview
MSW 4SV rs
Бренд: Extron electronics Страницы: 2
Westell A99-BAI-ACSF-UGKIT Install Instructions preview
A99-BAI-ACSF-UGKIT
Бренд: Westell Страницы: 3
Dahua PFS4226-24ET-240 User Manual preview
PFS4226-24ET-240
Бренд: Dahua Страницы: 3
FS S5850-24XMG Quick Start Manual preview
S5850-24XMG
Бренд: FS Страницы: 43
SIIG MultiView CE-H26311-S1 Manual preview
MultiView CE-H26311-S1
Бренд: SIIG Страницы: 24
Milestone pro MP-SU21T-KVM User Manual preview
MP-SU21T-KVM
Бренд: Milestone pro Страницы: 32
GarrettCom Ethernet Networks and Web Management Brochure preview
Ethernet Networks and Web Management
Бренд: GarrettCom Страницы: 12
Net Optics IBPO-HB50SR-XFP User Manual preview
IBPO-HB50SR-XFP
Бренд: Net Optics Страницы: 53
Hubner EGS 2 Operating And Assembly Instructions Manual preview
EGS 2
Бренд: Hubner Страницы: 23
Eaton TM-1-8290/E/SVB Instruction Leaflet preview
TM-1-8290/E/SVB
Бренд: Eaton Страницы: 2
odot ODOT-MS105T User Manual preview
ODOT-MS105T
Бренд: odot Страницы: 15
MiLAN MIL-S500 User Manual preview
MIL-S500
Бренд: MiLAN Страницы: 12
Lutron Electronics Nova N-1PS Installation Instructions preview
Nova N-1PS
Бренд: Lutron Electronics Страницы: 2
Pilz 542 183 Operating Manual preview
542 183
Бренд: Pilz Страницы: 41
MaxLink PSAT-6-4P-250 Quick Installation Manual preview
PSAT-6-4P-250
Бренд: MaxLink Страницы: 2
Neol ePowerSwitch 1GR2 User Manual preview
ePowerSwitch 1GR2
Бренд: Neol Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды