manualshive.com logo in svg

Extreme Networks BlackDiamond 10808, Руководство по установке оборудования

Желаете узнать как установить сетевое оборудование Extreme Networks BlackDiamond 10808? Скачайте бесплатно "Hardware Installation Manual" с официального сайта manualshive.com. Этот документ поможет вам настроить ваше оборудование быстро и правильно. Не теряйте времени, загружайте руководство прямо сейчас!

Поделиться
Скачать
background image

 

Table of Contents

Extreme Networks Consolidated ExtremeXOS Hardware Installation Guide

4

Calculating Amperage Requirements ...............................................................................38
UPS Transition Time .....................................................................................................38

Applicable Industry Standards ....................................................................................................39

Part 2: BlackDiamond Switches

Chapter 2: Overview of the BlackDiamond Switches ........................................................................ 43

Supported Features ...................................................................................................................43

Full-Duplex Support ..................................................................................................................44

Management Ports ....................................................................................................................44

External Compact Flash Memory Card .........................................................................................44

BlackDiamond 8806 Switch Chassis ...........................................................................................44

BlackDiamond 8810 Switch Chassis ...........................................................................................46

BlackDiamond 12804 Switch Chassis .........................................................................................47

BlackDiamond 12802 Switch Chassis .........................................................................................49

BlackDiamond 10808 Switch.....................................................................................................50

Chapter 3: BlackDiamond 8800 Modules........................................................................................ 53

Management Switch Modules (MSM) ..........................................................................................53

Slots for BlackDiamond 8800 MSMs ....................................................................................53
MSM Activity ......................................................................................................................54
MSM-G8X and MSM-48 Modules..........................................................................................54
MSM LEDs .........................................................................................................................56

I/O Modules..............................................................................................................................56

BlackDiamond 8800 Original Series I/O Modules ...................................................................57

G24X I/O Module ..........................................................................................................57
10G4X I/O Module ........................................................................................................58
G48T I/O Module ..........................................................................................................59
G48P I/O Module ..........................................................................................................59

BlackDiamond 8800 A-Series I/O Modules ............................................................................61

G48Ta I/O Module.........................................................................................................61
G48Xa I/O Module.........................................................................................................62
10G4Xa I/O Module.......................................................................................................63
10G4Ca I/O Module.......................................................................................................63

BlackDiamond 8800 E-Series I/O Modules ............................................................................64

G48Te I/O Module.........................................................................................................64
G48Pe I/O Module.........................................................................................................65

I/O Module LEDs .................................................................................................................66

Module LEDs ................................................................................................................66
Port LEDs on Non-PoE Modules ......................................................................................66
Port LEDs on PoE Modules (G48P and G48Pe) ................................................................67

Chapter 4: BlackDiamond 12800 Series Modules ........................................................................... 69

About BlackDiamond 12800 Series Modules ...............................................................................69

BlackDiamond 12800 Series MSMs............................................................................................70

Redundant MSM Activity .....................................................................................................71
MSM LEDs .........................................................................................................................71
MSM-5 and MSM-5R Modules .............................................................................................72

BlackDiamond 12800 Series I/O Modules ...................................................................................73

I/O Module LEDs .................................................................................................................73

Содержание BlackDiamond 10808









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BlackDiamond 10808

D-Box HaptiSync Hub User Manual preview
HaptiSync Hub
Бренд: D-Box Страницы: 27
3onedata TNS5800-8GP16GT-P24VDC Quick Installation Manual preview
TNS5800-8GP16GT-P24VDC
Бренд: 3onedata Страницы: 3
Aruba Instant On 1930 24G 4SFP/SFP+l Installation And Getting Started Manual preview
Instant On 1930 24G 4SFP/SFP+l
Бренд: Aruba Страницы: 48
GBC 34.0109.41 Quick Start Manual preview
34.0109.41
Бренд: GBC Страницы: 2
MuxLab HM44 User Manual preview
HM44
Бренд: MuxLab Страницы: 32
Jlso Tec Trade VH M 1 1 1 Series Operating Manual preview
VH M 1 1 1 Series
Бренд: Jlso Tec Trade Страницы: 15
Wavetronix Click 223 Installation preview
Click 223
Бренд: Wavetronix Страницы: 3
M-system SHSP Instruction Manual preview
SHSP
Бренд: M-system Страницы: 4
Advantech EKI-7659CPI User Manual preview
EKI-7659CPI
Бренд: Advantech Страницы: 101
Omega iServer MicroServer EIS-2B User Manual preview
iServer MicroServer EIS-2B
Бренд: Omega Страницы: 68
Omega OM-ESW-105-POE User Manual preview
OM-ESW-105-POE
Бренд: Omega Страницы: 17
Atlona AT-HD-SC-500 Manual preview
AT-HD-SC-500
Бренд: Atlona Страницы: 22
Santon D1-G/H-T Installation Manual preview
D1-G/H-T
Бренд: Santon Страницы: 16
NETGEAR GSM7352S - ProSafe Switch - Stackable User Manual preview
GSM7352S - ProSafe Switch - Stackable
Бренд: NETGEAR Страницы: 628
GatesAir Intraplex T1 DCS-9530 CrossConnect System Installation And Operation Manual preview
Intraplex T1 DCS-9530 CrossConnect System
Бренд: GatesAir Страницы: 106
H3C IE4300 Series Command Reference Manual preview
IE4300 Series
Бренд: H3C Страницы: 31
Kramer SID-X2N User Manual preview
SID-X2N
Бренд: Kramer Страницы: 31
Gigabyte GN-GT5D User Manual preview
GN-GT5D
Бренд: Gigabyte Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды