Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 333

Страница: 333 / 370

Operating Instructions

Maintenance and Repair

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 333 / 370

Wrap the folded cloth around
your index finger.

Moisten the cloth with a little
bit of cleaning fluid suitable
for the type of UV ink used.

IMPORTANT !



Never place the cloth
being used aside either
before or during clean-
ing!



Always use only clean
sections of the cloth for
cleaning.

> Check all of the LED light

strips of the pre-curing
unit

between the print heads

and clean them using a dry,
clean and lint-free cloth
(CSAT order no.

FF100252100

). The cloth may

be slightly (!) moistened with
cleaning fluid suitable for the
type of UV ink used as
needed.

Make sure that the narrow
light strips of all lamp modules
are spotless and streak-free
(see detail photo).

If a lamp module exhibits
scratches or dull areas, a ser-
vice technician must be called.

Clean up any drops of fluid
from the catch sheet under the
print head unit. If needed, use
cloths moistened with ace-
tone.

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды