Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 275

Страница: 275 / 370

Operating Instructions

Troubleshooting

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 275 / 370

Code Display:

CA = Current Alarm;
S= Status

essage

larm?

ause of the message /

emedial action:

To be
elimin.
by

104

“104= Degassing
unit: vacuum too
low!”

C: Vacuum in the degassing system is too low.

The reading displayed by the 500-
B26 is less than 0.79 points.

S, C

"30= Printer not
ready to START"

R: Check the vacuum pump +500-M8 and its

connection wires and plug contact
+500-A140/X2.

R: Fix any leaks. Replace porous hoses and

membranes.

105

“105= Degassing
sensor not ready!”

C: Vacuum in the degassing system is insuffi-

cient. The reading displayed by the sensor
+500-B26 is between 0.8 and 0.85 points.
Water is up to 500-B25.

S, C

"30= Printer not
ready to START"

R: Empty the separator of the degassing sys-

tem until the 500-B25 no longer
responds.

R: Fix any leaks. Replace porous hoses and

membranes.

110

CA "110= Missing

data IJ image
converter"

C: The data packet transmitted from the IJ-

image converters to the engine board con-
tains incorrect or incomplete data.

S, C

"30= Printer not
ready for START"

R: On the touchscreen open the tab

Consuma-

bles > Print heads

and read off the number

of shots fired by each print head: If a "0" is
shown anywhere, then the associated IJ
image converter board is defective and has
to be replaced.

S, C

111

CA "111= Communi-

cation error IJ
image converter"

C: The communication between the IJ convert-

er boards and the IJ engine board is out of
order.

S, C

"30= Printer not
ready for START"

R: Connect the connections between the vari-

ous IJ converter boards and the connection
between the IJ converter boards and the IJ
engine board.

C: The power supply to the IJ converter boards

in question is out of order or interrupted.

R: The power supply unit +300-G80 has failed

or at least one of the fuses +400-F510 to
+400-F514 has been triggered.
Check all of the components, wiring and
contacts mentioned, have defective parts
replaced (by CSAT customer service).

112

CA "112= Print head

in service posi-
tion"

C: This message is shown whenever the print

head unit has been uncoupled from its guide
frame and has been pulled back into the so-
called cleaning position.

O, T

"30= Printer not
ready for START"

R: Push the print head unit in its guide frame

forward until the black lock knob falls back
into place.

C: Sensor is out of order.

S, C

R: Check the 400-B43, wiring and

contacts, have defective parts replaced (by
CSAT customer service).

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды