Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 228 | Manualshive

Страница: 228 / 370

background image

Assembly

Operating Instructions

© Copyright by Markem-Imaje CSAT GmbH

Page 228 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

Notice

Machine can be damaged by using it in an unsuitable environment.

The machine should only be used in ambient conditions which are suitable for the
machine and the materials being processed.

6.1.1

Set-up at final destination

Warning

Potential hazard due to lack of stability.



The floor must be even and horizontal. The machine has to be

leveled in order to ensure trouble-free operation.



Place the printer on a flat, solid, underlying surface which is able to

withstand the expected load.

6.1.1.1 Load-bearing capacity of the underlying surface

The printer should be set up only on even, flat surfaces which have suffi-
cient load-bearing capacity in terms of distributed load and concentrated
load, see Chapter 3 "Technical Data".

6.1.1.2 Ambient conditions

The printer should not be operated unless all of the conditions defined in
Chapter 3 "Technical Data" are met.

6.1.1.3 Setting up the printer

>

Lift the print system from the transport crate or lift the print system from
the transport pallet

>

Position the print system at the set-up location. Impacts must be
avoided!

>

Level the printer until it is perfectly horizontal as described in the fol-
lowing section.

6.1.1.4 Aligning the printer horizontally

Required tools



200mm long precision spirit level with accuracy of 0.02mm/m in ac-

cordance with DIN 877.



2 wrenches SW30

Prerequisites



The screws between the front, side, and cover panel must be sealed

with a screw-lock coating.

«
...
226
227
228
229
230
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Panasonic Страницы: 9

Бренд: Panasonic Страницы: 2

imageRUNNER 4570

Бренд: Canon Страницы: 154

Бренд: Zebronics Страницы: 6

Бренд: Olivetti Страницы: 82

bizhub C452 Series

Бренд: Konica Minolta Страницы: 17

Бренд: Hanin Страницы: 27

Бренд: Canon Страницы: 65

Бренд: Oki Страницы: 107

Бренд: Source Technologies Страницы: 47

Pro C5300 Series

Бренд: Ricoh Страницы: 37

Бренд: Olivetti Страницы: 56

Бренд: Lexmark Страницы: 8

Бренд: Oki Страницы: 239

Бренд: Loadrite Страницы: 12

Бренд: Muratec Страницы: 188

Бренд: Muratec Страницы: 364

Бренд: Samsung Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды