Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 41

Страница: 41 / 370

Operating Instructions

Safety

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 41 / 370

2.6

Residual risks

Other risks occur when operating the ITS6 printer, which can be avoided
through safety-conscious work habits.

Warning

Risk of fatal injury due to electrical shock.



Observe the warning signs attached.



Do not remove any covers in the switch cabinet.



Work on electrical equipment must be performed only by author-

ized personnel qualified in electronics.

Warning

Danger of entanglement at printing substrate conveyance area.



Do not reach into the individual guide rollers of the printing sub-

strate.

Caution

Permanent damage to skin can be caused by contact with machine
operating materials of all types! (long-term injuries)



Wear solvent-resistant safety gloves and protective eyewear when

handling media. (see section 2.5.5, "Personal protection
equipment").



Avoid contact with operating materials and cleaning agents!



Wash exposed skin thoroughly. See a doctor if skin irritation per-

sists.



Change contaminated or soaked clothing immediately.



Observe the safety instructions of the materials used.

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды