Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 370

background image

Safety

Operating Instructions

© Copyright by Markem-Imaje CSAT GmbH

Page 26 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

2.4

Safety instructions

The basic requirement for the safe handling and trouble-free operation of
the ITS6 printer is awareness of the fundamental safety instructions and the
work safety regulations.

These operating instructions contain all of the important information needed
for operating the printer safely.

The internal work safety regulations must be observed.

Warning

Risk of fatal injury from contact with live parts.



Work on electrical equipment must be performed only by author-

ized personnel qualified in electronics.



Always keep switch cabinets closed. Only authorized personnel

with key or tool are allowed access to the switch cabinets.



Do not work on live parts.



Replace loose connections and damaged cable immediately. Turn

off and lock main switch before performing work.



Cables should not be jammed or crushed. Cables must be laid so

that they cannot be damaged or pose a tripping hazard.

Warning

The machine may not be operated without locked and functioning
safety equipment.



Risk of injury due to sudden movements of the handling systems

in set-up mode and during repairs and maintenance.



Set-up work on the machine should be performed at a slow speed.



The machine components may be programmed by specially

trained personnel only.

Warning

Warning of electromagnetic field. Persons staying in the direct vicinity
of the electromagnetic field may be charged.



Persons with pacemakers should stay away from the corona sta-

tion during printing operation..



A person who faints must be taken out of the danger area immedi-

ately. If the person continues to be unconscious, start resuscitati-
on.



Also, call a doctor or paramedic.

«
...
24
25
26
27
28
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: IBM Страницы: 112

ImageCLASS MF4570dw

Бренд: Canon Страницы: 164

imagePRESS C800 Series

Бренд: Canon Страницы: 132

ImageCLASS MF5730

Бренд: Canon Страницы: 2

RS/6000 44P Series 270

Бренд: IBM Страницы: 216

Бренд: Ultimaker Страницы: 30

Бренд: Oki Страницы: 4

Бренд: Kyocera Mita Страницы: 209

Бренд: Citizen Страницы: 133

Бренд: J&Maya Страницы: 21

Бренд: Konica Minolta Страницы: 44

Бренд: Evolis Страницы: 63

Бренд: Lexmark Страницы: 8

SEH InterCon PS54a-G

Бренд: SEH Страницы: 24

Бренд: VORON Страницы: 73

Бренд: idp Страницы: 48

634dte - X B/W Laser

Бренд: Lexmark Страницы: 148

Бренд: Xprinter Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды