Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 330

Страница: 330 / 370

Maintenance and Repair

Operating Instructions

Page 330 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

10.7.6 Inspection and cleaning of the main curing unit

Notice

Prevent any damage to the main curing unit due to incorrect cleaning.



Any cleaning of the main cleaning unit may only be performed after the printer

was switched off completely.



The lamp modules should be no more than warm to the touch during cleaning.



Only use the cleaning aids mentioned here.

Cleaning the main curing unit

Unlock and remove lamp
module.

Check the 3 glass covers
for cleanliness.

First remove loose dirt or
wet ink with a dry, lint-free
cloth (Order no.

FF100252100

)

If heavy deposits are pre-
sent, first remove them as
much as possible using a
ceramic stovetop scraper.

Afterwards, remove the
rest using a special clean-
ing pad no

ZE1010-75

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды