Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 370

background image

Operating Instructions

Safety

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 29 / 370

2.5

Safety concept

Warning

Death, serious injury or substantial material damage can occur if the
corresponding precautions are not taken.



Check the proper functioning of all safety measures on the ma-

chine.



Do not bypass any safety measures.



Wear the required personal safety protection equipment.



Adhere to the specified order of work.



Acquaint yourself with the handling of operating materials.

2.5.1

Safety zones

There are three different zones, depending on the degree of danger ema-
nating from the machine. Only persons authorized by the owner are entitled
to access the individual zones.

2.5.1.1 Traffic zone

The traffic zone is the area specified by the owner which is accessible to or
can be reached by anyone without opening hard guards, triggering sensors
on safety equipment, or using any other means to gain access.

2.5.1.2 Work zone

The work zone is the area specified by the owner in which persons work on
or operate the printer in normal mode (inspection, maintenance and clean-
ing are not included here).

2.5.1.3 Maintenance zone

The maintenance zone is the area specified by the owner to which only the
personnel authorized to perform maintenance work is allowed access. Ac-
cess requires a tool. The machine is not switched off when accessed, but
rather continues to run. Since a risk to personal health and safety is in-
volved, this area is accessible only to authorized and trained personnel.

«
...
27
28
29
30
31
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Samsung Страницы: 9

Bixolon SRP-500

Бренд: Samsung Страницы: 27

550N - CLP Color Laser Printer

Бренд: Samsung Страницы: 288

2 COLOR THERMAL PRINTER SRP-275

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 91

Бренд: Fenix Imvico Страницы: 88

DocuPrint C525 A

Бренд: Xerox Страницы: 49

DocuPrint C2100

Бренд: Xerox Страницы: 206

Бренд: Xerox Страницы: 116

Бренд: Xerox Страницы: 358

Бренд: Xerox Страницы: 344

Бренд: Xerox Страницы: 59

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 10

Бренд: Xerox Страницы: 51

Бренд: Xerox Страницы: 110

7300DX - Phaser Color Laser Printer

Бренд: Xerox Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды