Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 234

Страница: 234 / 370

Commissioning

Operating Instructions

Page 234 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

Caution

Danger of injuries and damage to the system.



The commissioning of the printer and connection of supply lines

should be carried out by trained technical personnel only.



Carefully reinstall and secure parts that were removed for trans-

porting purposes before re-commissioning.

Caution

Danger of crushing hands and fingers when closing the safety doors
and the hinged hood.



Do not reach into the areas where the safety doors and the hinged

hood close.

Notice

Potential damage to machine parts due to electrostatic charges.



Establish a potential equalization between the machine and the environment.



Do not operate the machine unless it is sufficiently grounded.

Notice

Machine parts can be damaged by using the wrong substrate and consumable
supplies.



Do not use any substrates that have not been approved by Markem-Imaje

CSAT GmbH or whose properties deviate from the materials ordinarily used.



Use only original ink and cleaning fluid from Markem-Imaje CSAT GmbH!

Notice

When adding on to the machine or installing components that haven’t been used
before, the safety of the machine must be newly assessed.

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды