Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 30

Страница: 30 / 370

Safety

Operating Instructions

Page 30 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

2.5.2

Safety measures

The purpose is to protect…



… the personnel against injuries,



… the machine against damage and downtime,



… the environment against hazards.

The following safety measures were taken based on a risk analysis of the
ITS6 printer:



Fixed / movable hard guards,



Use of monitored safety doors.



Emergency Stop button at control panel,



Obligation to wear personal protection equipment (PPE),



Attachment of safety signs to the machine,



Safety instructions on the machine,



Safety instructions in the operating instructions.

All of the aforementioned measures will be explained in detail below.

2.5.3

Safety equipment

All dangerous areas are protected by moveable, mechanical hard guards.

Passive safety equipment is for the protection of the environment.

The hard guards include:



The complete housing of the machine,



Cover and safety doors with interlocking guard and monitoring.

The passive safety guards include:



Collection container for cooling water underneath the cooling water in-
let and outlet,



Collection pan for ink and cleaning fluid under the printing unit. Small
collection pans under the ink management and the residual ink bottle.

Warning

The safety equipment prevents access to dangerous areas by unau-
thorized personnel.



Never manipulate or deactivate safety guards or safety equipment.



The conversion or deactivation of safety equipment can lead to se-

rious injuries.

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

Результаты поиска

Содержание markem imaje CSAT ITS6 210

Отзывы:

Похожие инструкции для markem imaje CSAT ITS6 210

Бренды по названию

Популярные бренды