Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 370

background image

Operating Instructions

Troubleshooting

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 261 / 370

9.1.3

Messages under the tab

Alarms

The

Alarms

screen displays all of the malfunctions and status messages

currently being registered which result in the printing process either being
stopped or not being able to be started at all. The printing process cannot
be started until no more messages are being displayed on the Alarms
screen and all problems have been eliminated.

Information

If any kind of a problem occurs t

hat‘s indicated on the

Alarms

screen,

then the "Alarms" navigation key in the touchscreen will be marked with

a prominent yellow triangle

in order to bring this condition to the op-

erator‘s attention and to have him open the

Alarms

screen.

9.1.4

Messages in

the “Current Alarm” and “Stopreason” lines

The  uppermost  line  "Current  Alarm"  describes  briefly  in  words  and  some-
times in conspicuous red letters all conditions that do not correspond to the
normal operation of the printer. These could be error messages or else just
the  notice  that  a  door  has  been  opened  on  the  stopped  printer.  Although
this is not an error, it is a condition that will prevent the printer from being
started again and therefore has to be shown.

Each message shown in the "Current Alarm" line is displayed only until the
irregularity has been eliminated or until another error signal with higher pri-
ority is received and simply writes over the previous text.

If an error message is shown in the “Stopreason” line, then usually it in-
volves a more critical situation, which entails a potential hazard for the op-
erating personnel or the plant. Therefore, the printer is stopped abruptly.
Thereafter, the plant would not be able to be restarted until the problem has
been eliminated.

Any message shown in t

he “Stopreason” line will not be deleted until the

cause of the error has been eliminated and the printer has been restarted.

But if you want to view all of the errors that occurred in the past and which
are still pend

ing, all you have to do is press “

Alarms

”, and then a separate

window with all the latest messages will open on the screen.

The  following  table  gives  an  overview  of  all  the  messages  which  can  be
shown  in  the  status  displays  “Current  Alarm”  and  “Stopreason".  Besides
short explanations and instructions on how to handle the error, the last col-
umn specifies who can eliminate the individual errors.

«
...
259
260
261
262
263
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

WORKCENTRE 5735

Бренд: Xerox Страницы: 50

Бренд: SEH Страницы: 50

WorkCentre 7655

Бренд: Xerox Страницы: 19

MAGICARD 300plus

Бренд: Ultra electronics Страницы: 45

201021 - P 330N Photo Printer

Бренд: Olympus Страницы: 79

Бренд: Tally Страницы: 174

Бренд: IBM Страницы: 2

Бренд: Riso Страницы: 66

Бренд: MIMAKI Страницы: 30

microFlash Series

Бренд: Oneil Страницы: 135

Бренд: BT Страницы: 64

PIXMA E300 series

Бренд: Canon Страницы: 28

Бренд: Canon Страницы: 115

Бренд: Canon Страницы: 124

Бренд: Canon Страницы: 216

PIXMA iP7200 Series

Бренд: Canon Страницы: 5

ActionLaser 1000

Бренд: Epson Страницы: 70

ActionLaser 1000

Бренд: Epson Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды