Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 370

background image

Machine Description

Operating Instructions

© Copyright by Markem-Imaje CSAT GmbH

Page 134 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

4.7.2

Control panel

The ITS6 printer is operated by means of a control panel.

The control panel is mounted on a hinged and pivoting cantilever arm,
which can be attached to either the right end or left end of the printer ac-
cording to customer requirements.

Fig. 51. ITS6 printer control panel

Pos. Elements

Meaning

1

Emergency
Stop button

Switches off all drives, high voltage parts and the pneu-
matic system when pushed. The touchscreen, indicators
and door interlocks remain switched on and active.
To reset from the Emergency Stop mode, the red button
has to be turned until it pops back out and a green ring
becomes visible.

2

Start printer

Pushbutton that is active only in roll-to-roll mode.
After this button is pressed the printer will start working.



This button will blink until the material starts to be
conveyed.



This button is constantly illuminated during the print-
ing process.



This button remains dark when the printer is stopped.

Whenever the printer has been stopped, it can be re-
started with this button. The printing process will resume.

3

Stop print sys-
tem

Pushbutton that is only active in roll-on-roll operation.
Pressing the

“Stop”

button stops the printing operation in

a controlled way
The printer will continue running for a few seconds, finish
printing the last images, and then initiate the web retrac-
tion.



This button is illuminated only in the time between
being pushed and the end of the web retraction.



The rest of the time and in all other operating modes
this button remains dark.

1

2

3

4

5

6

7

«
...
132
133
134
135
136
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 48

Stylus Pro 7900

Бренд: X-Rite Страницы: 36

Бренд: NCR Страницы: 224

SelfServ Checkout 7350

Бренд: NCR Страницы: 20

Бренд: TASKalfa Страницы: 36

Бренд: TE Connectivity Страницы: 2

Бренд: TE Connectivity Страницы: 2

Бренд: WANHAO Страницы: 24

Бренд: µ-Dimension Страницы: 74

Бренд: Roland Страницы: 36

wematter Atmosphere

Бренд: 3D Systems Страницы: 11

Бренд: Felix printers Страницы: 28

Falcon Outdoor 46

Бренд: MUTOH Страницы: 333

Бренд: Magicard Страницы: 124

Бренд: TAKE-A-LABEL Страницы: 12

Бренд: Oki Страницы: 137

Бренд: Konica Minolta Страницы: 432

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды