Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 370

background image

Operating Instructions

Troubleshooting

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 269 / 370

Code Display:

CA = Current Alarm;
S= Status

M

essage

or

A

larm?

C

ause of the message /

R

emedial action:

To be
elimin.
by

52

CA "52= Main curing:

temperature too
high"

A

C: The temperature of at least one of the lamp

modules in the main curing unit has reached
the “Alarm" warning point entered in the tab

Job > UV Curing

.

S, C

S:

"30= Printer not
ready for START"

R:

Check the “Alarm” warning point. Recom-
mended range of adjustment: 35°C - 39°C.
Is the cooling unit working? Has it been ad-
justed correctly and is enough coolant flow-
ing? Does the coolant line have a leak?
Has the setpoint for the curing power been
set too high?

54

CA "54= Emergency

stop in the printer"

A

C: Emergency Stop button of the printer was

actuated.

O, T, S,
C

S:

"30= Printer not
ready to START"

R: Pull out the Emergency Stop button of the

printer. Switch the printer off and on again
briefly with the "ON/OFF switch". Not until
then will the message disappear and can the
system be restarted.

55

CA "55= Emergency

stop in the finish-
ing system”

A

C: Emergency Stop button of the finishing sys-

tem was actuated.

S

"30= Printer not
ready to START"

R: Pull out the Emergency Stop button of the

finishing system. Switch the printer off and
on again briefly with the "ON/OFF switch".
Not until then will the message disappear
and can the system be restarted.

56

CA "56= No com-

pressed air"

A

C: No compressed air available

O, T, S,
C

S:

"30= Printer not
ready to START"

R: Restore the compressed air supply

C: Is fuse +400-F503 OK?

S, C

R: Check fuse +400-F503 and replace if nec-

essary.

59

CA "59= Friction

drive: Pressure
roll unlocked"

A

C: The frame with the pressure roll is unlocked.

The printing substrate is no longer being
pressed by the pressure roller against the
rubber roller and, therefore, can slip off of it.

O, T, S,
C

S:

"30= Printer not
ready to START"

R: Press down the frame with the pressure

roller until the two black latches lock into
place.

C: Sensor system out of order.

S, C

R: Check 300-B46, lines and contacts,

have defective parts replaced (by CSAT
customer service).

63

CA "63= Printing unit:

hinged hood
open"

A

C: The hinged hood of the printer is open. The

100-A3 responded.

O, T, S,
C

S:

"30= Printer not
ready to START"

R: Close the hinged hood.

O, T

If this message is shown even though the
hood is closed, then please check the sen-
sor +100-A3 and the associated wires.

S, C

«
...
267
268
269
270
271
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 96

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 78

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 49

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 161

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 84

Бренд: Oki Страницы: 51

Бренд: Oki Страницы: 86

Бренд: Oki Страницы: 40

Бренд: Oki Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды