Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 370

background image

Operating Instructions

Operation

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 245 / 370

8.6

Changing the roll of printing substrate

The roll of printing substrate has to be inserted in the unwinding unit so that
it unrolls either counterclockwise or clockwise, depending on whether the
outside or the inside of the printing substrate is supposed to be printed.

The direction of rotation of the roll depends on the winding direction of the
printing substrate.

The printer may stay turned on during the replacement.

Notice

Use only substrates with edges not prone to bowing or becoming
wavy when stretched in place. The max. amount of permissible bow-
ing or waviness is 0.2 mm to avoid rubbing against the nozzle plates
of the print heads.



Do not open and remove the protective film of the substrate roll

until ready to use the roll.



Store any leftover material rolls in a warm, dry place or seal the roll

airtight in plastic film until ready to use again.



If necessary, dry the ends of the roll of printing substrate with a hot

air gun.

Notice

For each substrate web roll, measure the material thickness first!

Be sure that at the printing table the proper deflection rollers rollers
are installed, compare chapter “4.6.15.1 Printing table with exchange-
able deflection rollers

Only the operator of the plant is responsible for damages caused due
to ignoring this requirement!

«
...
243
244
245
246
247
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Unisys Страницы: 255

Бренд: Xerox Страницы: 199

Бренд: Oki Страницы: 100

Бренд: Oki Страницы: 2

Бренд: Xerox Страницы: 316

Бренд: Xerox Страницы: 74

Бренд: Xerox Страницы: 306

Бренд: Xerox Страницы: 16

Бренд: Xerox Страницы: 4

Бренд: Oki Страницы: 38

Бренд: Oki Страницы: 38

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 36

Jetprinter Disney Edition Z615 Series

Бренд: Lexmark Страницы: 2

Бренд: TE Connectivity Страницы: 2

Бренд: TE Connectivity Страницы: 2

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды