Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 370

background image

Operating Instructions

Technical Data

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 61 / 370

3.9.9

Unsuitable printing substrates

Never insert a printing substrate in the printer if at least one of the following
points applies:



With printing tables with deflection rollers: Total thickness of the mate-
rial above the values mentioned in chapter 3.8.



Printing substrates with edges are bowed up by more than 0.2 mm
(edges that are bowed or wavy).



Insufficient tensile strength: The material stretches, frays, or threatens
to tear.



Perforated material.



Labels or self-adhesive materials without a barrier coat on the side to
be printed.



Insufficient temperature resistance: At temperatures above 50°C the
material begins to stretch, to form blisters or waves, to tear, or to melt.



Printing substrates with fibers protruding from the surface.



Printing substrates and coatings which partially dissolve or become
chemically altered through the use of inks and cleaning fluids.



Materials which, under the influence of pressure and/or high tempera-
tures, emit gases, liquids or even solid particles



Labels which, when deformed or subjected to heat, come loose on
their own from the backing material.



Label material in which the backing is deeply incised or heavily em-
bossed.



Printing substrates which buckle or form waves perpendicular to the di-
rection of travel and cannot be smoothed, even when pulled in the di-
rection of travel.



Printing substrates that tend to form creases.



Printing substrates with uneven or fringed edges.



Basically, all rolls of material which exhibit any defects on the end fac-
es or on the surface, for example pressure marks, creases, or tears as
a result of falling or impacts.

Fig. 6 shows a typical unsuitable printing material. Faults during manufac-
turing  or  storage  do  not  allow  this  printing  material  to  be  smoothed  on  an
electrostatic  plate.  When  used  for  printing,  such  a  printing  material  would
most likely damage the print heads. Consequently, do not use it!

«
...
59
60
61
62
63
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: QMS Страницы: 311

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 6

Бренд: Oki Страницы: 167

Бренд: Oki Страницы: 116

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 331

Бренд: Oki Страницы: 36

C5800Ldn Series

Бренд: Oki Страницы: 143

Бренд: Oki Страницы: 101

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 282

Бренд: Oki Страницы: 269

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 3

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды