Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 370

background image

Machine Description

Operating Instructions

© Copyright by Markem-Imaje CSAT GmbH

Page 120 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

4.6.17.2 Correct operation of the pre-curing unit

Operating the pre-curing unit involves the risk of light being emitted by its
LEDs, which can be partially reflected and slowly harden the film of ink on
the underside of the print heads. This would cause the nozzle plates to be-
come clogged over time and the print heads, costing several thousand Eu-
ros each, would have to be replaced

– damage that is not covered by any

warranty and, therefore, always has to be covered by the owner of the sys-
tem!

Notice

Prevent any damage to the print heads!



Only use the pre-curing unit when absolutely necessary, namely:

The edges of the inks run into each other and mix in areas
where inks of different color are directly adjacent to one anoth-
er.

The printing substrate is very smooth so that the drops of ink
could roll off or fail to merge into solid patches of color.



Make sure that the pre-curing unit is operated at the lowest possi-

ble power level.



Make sure that all print heads undergo a standard or intensive

cleaning at least every two hours.

Notice

If thin, white lines appear lengthwise in the prints, then



Stop the printing process immediately and have all print heads un-

dergo a standard or intensive cleaning.



Keep repeating these procedures until all of the print heads are

clean again. See Chap.10.7.5.1, "Mechanical cleaning of the noz-
zles"



Extremely dirty print heads might also need to be cleaned by hand.

See Chap.10.7.5.2, "Manual cleaning of the print heads".

In  order  to  prompt  the  operator  to  print  without  the  pre-curing  wherever
possible,  this  unit  is  deactivated  automatically  by  the  controls  whenever  a
new image file is loaded. If pre-curing is nevertheless required for the next
print  job,  then  the  operator  must  re-activate  it  after  loading  the  image  file
using the tab

Job > UV Curing

.

On the other hand, if the required format file is not loaded until after the im-
age file, the settings saved in the format file would override in this case: If it
provides for printing with a pre-curing unit, then the latter would in fact be
switched on by the controls and not be deactivated automatically.

«
...
118
119
120
121
122
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Partner Страницы: 9

Accel-a-Writer 8300

Бренд: Xante Страницы: 12

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 16

Бренд: SEH Страницы: 5

Бренд: Make Mendel Страницы: 29

Бренд: Dascom Страницы: 146

V16 Automatic Shaker Unit

Бренд: Garment Printer Ink Страницы: 21

PG 2028 SPECIAL

Бренд: Olivetti Страницы: 104

IMAGE M4100 Series

Бренд: G&G Страницы: 147

Falcon Outdoor 46

Бренд: MUTOH Страницы: 333

Бренд: AnyCubic Страницы: 253

apeosport 550 I

Бренд: Xerox Страницы: 160

Бренд: iDPRT Страницы: 41

Бренд: Oce Страницы: 61

Бренд: Aficio Страницы: 92

Бренд: Ricoh Страницы: 4

Бренд: Star Страницы: 2

Automatic Photo Book Station

Бренд: Durst Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды