Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 286 | Manualshive

Страница: 286 / 370

background image

Maintenance and Repair

Operating Instructions

© Copyright by Markem-Imaje CSAT GmbH

Page 286 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

Maintenance Schedule ITS6

Every 2 hours

All print heads must undergo a standard or intensive cleaning very two
hours at the latest (see Chap. 10.7.5.1 Mechanical cleaning of the nozzles

Daily

At the end of the shift, all of the print heads must first undergo a standard
cleaning and then be cleaned by hand.

Move the print head unit to service position, check the wipers for print head
cleaning for dried up ink residues and clean them manually.



The wipers must be straight and sharp-edged. They must not show any

cracks or foreign bodies.



Each wiper must be aligned in parallel to the upper edge of the related

clamping plate.



Replace wipers if necessary.

At the end of the shift, check all of the LED strips of the pre-curing unit for
any dirt and clean if necessary.

Check inlet suction. Remove any dirt

Check all guide rollers for spotlessness, clean if necessary.

Check the adhesive film of the printing substrate cleaning module on a
regular basis. If heavily soiled or lacking adhesive power, tear off one layer
of the adhesive foil.

Move the print head unit into the service position, check the wipers used
for cleaning the print heads for areas of dried-on ink and clean by hand
(see chap.10.7.5.2

„Manual cleaning of the print heads”.). The edges of

the wipers

have to be straight and sharp and shouldn’t have any cracks or

especially any foreign objects on them. Furthermore, the cleaning edge of
each wiper must be aligned parallel to the upper edge of the clamping
plate. Replace wiper if necessary, see chap. .10.6.3

“Changing the wipers

on the print heads

Move back the print head unit into the service position and check the roll-
ers of the printing table and the sheet below for spotlessness. Clean with
cleaning fluid or acetone if necessary.
Check to see whether the entire print image is narrower than the substrate
to be processed and that it is positioned entirely on the web so that no ink
is sprayed alongside the substrate onto the printing table without being
fixed there. Furthermore, when the printing table is soiled with ink, the
guide rollers behind the printing table should be checked for soiling also.

Check the glass shields of the UV lamps for soiling. Completely remove
heavier grime deposits using a special cleaning pad (order no.

ZE1010-75

)

if necessary.

Check the rubber rollers of the web tension controller and the friction drive
for soiling. If necessary, clean with isopropyl alcohol.

Check the electrodes of the two substrate dischargers for soiling. Remove

«
...
284
285
286
287
288
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

DocuPrint C2200

Бренд: Xerox Страницы: 200

Бренд: Oki Страницы: 94

proColor pro900DP

Бренд: Oki Страницы: 18

VarioPrint 6180

Бренд: Oce Страницы: 306

Бренд: iDPRT Страницы: 74

Бренд: Memjet Страницы: 181

Бренд: A&D Страницы: 8

Бренд: Konica Minolta Страницы: 28

Digital Minilab Frontier LP5700R

Бренд: FujiFilm Страницы: 2

ZPS3611 - QUICK

Бренд: Zonet Страницы: 1

Бренд: Wang Страницы: 39

Бренд: Canon Страницы: 769

Stylus CX7300 Series

Бренд: Epson Страницы: 20

Stylus CX6900 Series

Бренд: Epson Страницы: 40

Stylus NX125 Series

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 8

Stylus ME OFFICE 510

Бренд: Epson Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды