Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 370

background image

Operating Instructions

Assembly

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 231 / 370

6.2

Installation of the printer’s supply systems

Warning

Installation of the supply lines.



The printer must be connected properly to all supply lines by quali-

fied technical personnel.



The commissioning procedure should be carried out in accordance

with the operating instructions only.

6.2.1

Electrical connection

The ITS6 printer must be connected properly to the power supply with the
correct voltage and frequency.

>

Plug the lead of the printer into a compatible and fuse-protected socket
of the three-phase current supply network.
(Observe specifications on the type plate of the printer!)

6.2.2

Pneumatic system

All of the pneumatic equipment on the ITS6 printer is pre-installed.

The ITS6 printer requires dry, oil-free air.

Flow rate and pressure are maximum 10 dm³/min and 6

– 8 bar respective-

ly.

>

Connect the line coming from the on-site compressed air supply to the
coupling plug on the printer.

>

Check for leaks and the secure fit of all hose connections.

Notice

Make sure to connect a pneumatic supply line with a 2’’ diameter and
permanent excess pressure of at least 5 bar. The supplied com-
pressed air must be free of oil and dry.

6.2.3

Interfaces

>

Now connect all signal cables to the associated interface plugs on the
printer and secure the connector housings with the provided retainers.

6.2.4

Transport securing devices

>

Remove the transport securing device on the printer head unit.
Loosen both knurled screws and pull the transport securing device out
of the two holes on the side of the print head unit. Turn the transport
securing device around so that its rods are pointing to the right and

«
...
229
230
231
232
233
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Raymarine Страницы: 135

Бренд: UltraTape Страницы: 52

Бренд: Ultimaker Страницы: 101

Saddle Finisher-AF2

Бренд: Canon Страницы: 244

Бренд: EFI Страницы: 4

Бренд: Creality Страницы: 24

Бренд: WANHAO Страницы: 18

Бренд: Pantum Страницы: 164

Бренд: M&R Страницы: 36

Бренд: Ultimaker Страницы: 4

Бренд: Xerox Страницы: 18

Бренд: Wasp Страницы: 2

Бренд: Tinkerine Studio Страницы: 17

Бренд: Kyocera Страницы: 12

Бренд: Konica Minolta Страницы: 46

Бренд: Canon Страницы: 436

Pixma TS8700 Series

Бренд: Canon Страницы: 589

Бренд: Canon Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды