manualshive.com logo in svg

Dover markem imaje CSAT ITS6 210, Руководство по эксплуатации

"Чернильный принтер Dover Markem Imaje CSAT ITS6 210 обеспечивает высокое качество печати. Для правильной настройки и использования устройства необходимо ознакомиться с инструкция. Вы можете бесплатно скачать Руководство по эксплуатации с нашего сайта. Посетите manualshive.com, чтобы загрузить руководство."

Поделиться
Скачать
background image

Machine Description 

Operating Instructions 

 

 

 

© Copyright by Markem-Imaje CSAT GmbH 

 

Page  90 / 370 

Subject to Technical Modifications 

ITS6_135_Manual_EN.doc 

 

 

Pos.  Element 

Meaning 

1 

Display 

Setup Mode

: Displays the various control parame-

ters 

Automatic mode

: Displays the manually induced 

shifting of the side of the web, measured in millime-
ters. 

2 

“Increase 
value,” “Re-
duce value” 

These buttons are needed in the setup mode only. 
During the printing process they have no effect and 
are irrelevant to the operator. 

3 

+5V DC 

The operating voltage is enabled. This indicator light 
must always be illuminated. 

4 

Sensor dis-
plays 

A green triangle on the left side indicates on which 
side of the web the sensor is located. Two red illu-
minated triangles on the right-hand side indicate in 
which direction the web has drifted in relation to the 
position of the sensor. If neither one of these trian-
gles is illuminated, then the printing substrate is in 
the proper position. 
In the given device, only the bottom sensor display 
illuminates.  

5 

Direction of 
travel of web 

Indicates which direction of travel of the web was 
programmed for the device. 
In this case, only the right/down arrow should be 
illuminated. 

6 

Manual shift-
ing of the 
web position 
 

 

Shifts the web in the direction of the arrow selected.  
The buttons are active only in automatic or manual 
mode. The display changes only in automatic mode, 
however. Furthermore, the selected shifting of the 
web can be deleted in automatic mode by pressing 
the two buttons simultaneously. 

7 

STOP 

Whenever this indicator light blinks, then the auto-
matic control is disabled. The device can only be 
operated in manual mode or in the central position. 

8 

SETUP 

For setting the basic parameters.  
Not relevant for the operator. 

9 

Automatic 
mode 
 

 

 

Whenever the green LED is illuminated, then the 
automatic control is active. Whenever this LED 
blinks, then the control is disabled due to an exter-
nal signal and is inactive. 

10 

Center mode 
 

 

 

The pivoting frame is put in its neutral center posi-
tion and cannot be manipulated either by the sensor 
or by hand. 

11 

Manual mode  There is not automatic control. 

The pivoting frame stays fixed in the position it was 
moved to manually. 

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Canon ImageCLASS MF3240 Series Advanced Manual preview
ImageCLASS MF3240 Series
Бренд: Canon Страницы: 62
Canon ImageCLASS MF4270 Operation Manual preview
ImageCLASS MF4270
Бренд: Canon Страницы: 226
Canon imageCLASS D660 Setup Instructions preview
imageCLASS D660
Бренд: Canon Страницы: 8
Canon ImageCLASS MF3240 Series Basic Manual preview
ImageCLASS MF3240 Series
Бренд: Canon Страницы: 136
Canon Color imageRUNNER C5180 Series Service Manual preview
Color imageRUNNER C5180 Series
Бренд: Canon Страницы: 851
Canon imageCLASS D320 Printer Manual preview
imageCLASS D320
Бренд: Canon Страницы: 121
Canon imageCLASS MF212w User Manual preview
imageCLASS MF212w
Бренд: Canon Страницы: 236
Canon imageCLASS D760 Reference Manual preview
imageCLASS D760
Бренд: Canon Страницы: 82
Canon imageclass LBP251dw Settings Manual preview
imageclass LBP251dw
Бренд: Canon Страницы: 72
Canon ImageCLASS MF4270 Basic Operation Manual preview
ImageCLASS MF4270
Бренд: Canon Страницы: 248
Canon ImageCLASS MF4270 Starter Manual preview
ImageCLASS MF4270
Бренд: Canon Страницы: 36
Canon imageCLASS D760 Setup Instructions preview
imageCLASS D760
Бренд: Canon Страницы: 8
Canon imageCLASS MF4100 Series Service Manual preview
imageCLASS MF4100 Series
Бренд: Canon Страницы: 140
Canon imageclass LBP251dw Getting Started preview
imageclass LBP251dw
Бренд: Canon Страницы: 116
Canon imageCLASS D860 Basic Manual preview
imageCLASS D860
Бренд: Canon Страницы: 73
Canon imageCLASS D1320 Starter Manual preview
imageCLASS D1320
Бренд: Canon Страницы: 36
Canon ImageCLASS MF3240 Series Starter Manual preview
ImageCLASS MF3240 Series
Бренд: Canon Страницы: 15
Canon imageCLASS D550 Basic Operation Manual preview
imageCLASS D550
Бренд: Canon Страницы: 116

Бренды по названию

Популярные бренды

Загрузить еще бренды